What Are the Reasons for Purchasing the Milk Filling Machine?

Views: 4752 Author: Howie SUN Publish Time: Update Time:
Viscous filling is decided by three numbers: viscosity, particle size and the cleaning regime, and the machine follows from them. Pressure filling machine refers to filling under the condition of lower than normal pressure.
Key facts at a glance
Filling systemPiston dosing, or load cell for high-value product
ViscosityUp to 10,000 cP with the right bore
ProductsSauces, pastes, pulp juice, honey, detergents
PackagePET, glass, jar, pouch by configuration
Key controlDose repeatability, drip-free cut-off, product temperature
CleaningCIP circuit with a bypass for high-solid product

Why does a piston filler suit thick product better than a valve?

A piston draws a fixed volume into a cylinder and pushes it out, so the dose does not depend on how fast the product flows. A gravity or pressure valve depends on flow time, and thick product makes that time unpredictable. For anything above a few thousand cP, the piston is the simpler answer.

How is a high-solid line cleaned?

High-solid product does not flush like water. The CIP circuit needs a pre-rinse at temperature, a bypass around the filler bowl, and a return path that does not leave product in a dead leg. Cleaning time on a sauce line is often longer than the production changeover, and both belong in the capacity plan.

Product typeDosingMain risk
Smooth saucePistonDrip at the nozzle
Chunky saucePiston with large boreBridging at the valve seat
Honey and syrupPiston or load cellStringing and slow cut-off
Pulp juicePistonFibre settling in the bowl

The Filling Machine for Viscous Product is the matching unit when this becomes a line project.

What changes when the same line runs two recipes?

Dose volume, piston stroke, suck-back, conveyor speed and often the nozzle set. A recipe change on a piston line is mostly mechanical, so it takes longer than a recipe change on a volumetric water line. Two very different products usually justify two fillers rather than one flexible one.

A different bottle format means a different unit; see the Filling Machine for Viscous Product.

How is a piston filler sized for a chunky product?

From the largest particle, then from the dose volume. The bore has to pass the piece without bridging, and the valve seat has to close on the product rather than on the liquid around it. Speed comes last.

The same question is worked through from another angle in How to Select the Right Load Cell Combibloc for.

How to read the numbers. The output figures are specification ranges; the measured rate depends on the product and the shift. A rated BPH for sauce or paste assumes one recipe and one temperature; changeover and CIP sit outside it, so size on 0.60-0.80.

Frequently asked questions

Can one piston filler run sauce and juice with pulp?

Yes, if the bore and the valve seat are sized for the largest particle. A filler set for smooth sauce will bridge on pulp, so the particle size is a specification input, not a detail.

What is the difference between piston and load cell for sauce?

Piston doses by displacement and is faster; load cell doses by weight and is more accurate when density varies. For a chunky product with variable density, weight filling avoids give-away.

What is the largest particle a piston filler can pass?

It is set by the bore and the valve seat, not by the piston. Specify the largest piece in the product and size the seat above it, or the filler bridges and the dose falls short.

Why does sauce drip from the nozzle after the dose?

The suck-back stroke is too short for the viscosity, or the nozzle bore is too large. Both are settings, and both change when the recipe changes.

Key takeaways
  1. Thick product is dosed by displacement, not by flow time.
  2. Piston seal wear shows up as a slow downward drift, not a sudden error.
  3. Drip is a suck-back setting before it is a nozzle problem.
  4. Cleaning time on a high-solid line belongs in the capacity plan.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.