How to Select the Right Load Cell Combibloc for Viscous Products

Views: 1889 Author: Howie SUN Publish Time: Update Time:
Thick product is dosed by displacement, not by flow time, which is why a piston filler handles sauce where a gravity valve cannot. Handling high-viscosity products in a bottling plant can present unique challenges that require specialized solutions.
Key facts at a glance
Valve typePiston dosing, or load cell for high-value product
ViscosityUp to 10,000 cP with the right bore
ProductsSauces, pastes, pulp juice, honey, detergents
Bottle or canPET, glass, jar, pouch by configuration
Key controlDose repeatability, drip-free cut-off, product temperature
CleaningCIP circuit with a bypass for high-solid product

Why does a piston filler suit thick product better than a valve?

A piston draws a fixed volume into a cylinder and pushes it out, so the dose does not depend on how fast the product flows. A gravity or pressure valve depends on flow time, and thick product makes that time unpredictable. For anything above a few thousand cP, the piston is the simpler answer.

What decides dose repeatability on a piston filler?

Four things: the piston seal, the product temperature, the supply pressure at the inlet, and the presence of solids at the valve seat. A worn seal leaks past the piston and the dose falls slowly, which is why the drift is invisible from one bottle to the next and obvious over a shift.

Product typeDosingMain risk
Smooth saucePistonDrip at the nozzle
Chunky saucePiston with large boreBridging at the valve seat
Honey and syrupPiston or load cellStringing and slow cut-off
Pulp juicePistonFibre settling in the bowl

Rated output, change parts and services are listed on the Edible Oil Load Cell page.

What changes when the same line runs two recipes?

Dose volume, piston stroke, suck-back, conveyor speed and often the nozzle set. A recipe change on a piston line is mostly mechanical, so it takes longer than a recipe change on a volumetric water line. Two very different products usually justify two fillers rather than one flexible one.

Handling high-viscosity products in a bottling plant can present unique challenges that require specialized solutions.

For the same duty in another bottle format, the Filling Machine for Viscous Product is specified separately.

How is a piston filler sized for a chunky product?

From the largest particle, then from the dose volume. The bore has to pass the piece without bridging, and the valve seat has to close on the product rather than on the liquid around it. Speed comes last.

The same question is worked through from another angle in Key Advantages of Piston Filling Machines for Viscous Products.

How to read the numbers. The numbers in the tables are reference ranges taken from the product specification. Product changeover and CIP on a viscous line take longer than on a water line, so plan on 0.60-0.80.

Frequently asked questions

Can one piston filler run sauce and juice with pulp?

Yes, if the bore and the valve seat are sized for the largest particle. A filler set for smooth sauce will bridge on pulp, so the particle size is a specification input, not a detail.

Does a viscous line need CIP?

It needs a cleaning circuit designed for the product. High-solid product needs a pre-rinse and a bypass; a low-solid sauce may clean in place with the same circuit as a juice line.

Why does sauce drip from the nozzle after the dose?

The suck-back stroke is too short for the viscosity, or the nozzle bore is too large. Both are settings, and both change when the recipe changes.

Can a viscous line fill jars as well as bottles?

Yes, with a jar infeed, a different gripper and a different capping head. The filler itself is the same; the handling around it is not.

Key takeaways
  1. Thick product is dosed by displacement, not by flow time.
  2. Drip is a suck-back setting before it is a nozzle problem.
  3. Particle size is a specification input, not a detail.
  4. A recipe change on a piston line is a mechanical change.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.