How to Select the Right Load Cell Combibloc for Edible Oil

Views: 1750 Author: Howie SUN Publish Time: Update Time:
Oil filling fails on drip and density, not on speed. A load cell fixes the density problem; the valve cut-off fixes the drip. When dealing with high-viscosity liquids like edible oil, opt for load cell combiblocs that feature anti-drift mechanisms to counteract the effects of temperature variations and external forces.
Key facts at a glance
Valve typeLoad cell net-weight, or piston dosing
Output range12,000-36,000 BPH at 0.2-2 L
ViscosityUp to 10,000 cP
AccuracyPlus or minus 0.5 g per bottle
ContainerPET or glass
Key controlWeight per bottle, temperature, drip-free cut-off

Why does edible oil need weight filling instead of volume filling?

Oil density changes with temperature, so a fixed volume delivers a different mass in the morning and in the afternoon. A load cell weighs what goes into the bottle and stops at the target mass. That is why an oil line is specified in grams and a water line in millilitres.

In the meticulous world of bottled water production, ensuring accurate weight measurement and proper handling of high-viscosity liquids such as edible oil is paramount.

How does viscosity change the line design?

Above a few thousand cP the product moves by pressure and time rather than by gravity, so the bowl, the feed pipe and the valve bore all grow. Temperature control also becomes part of the filling specification, because a cold oil at 10 C and the same oil at 25 C behave like two different products.

When dealing with high-viscosity liquids like edible oil, opt for load cell combiblocs that feature anti-drift mechanisms to counteract the effects of temperature variations and external forces.

Dosing methodAccuracy basisWhen it fits
Load cellNet weight per bottleDensity moves with temperature
PistonDisplacement volumeStable density, high speed, thick product
Volumetric valveChamber volumeLow-viscosity oil at steady temperature
Flow meterMeasured volumeContinuous flow, limited pulp or solids

Throughput and change-part lists are on the Edible Oil Load Cell page rather than in this note.

What is the acceptance test for an oil filler?

Weigh a fixed sample at the start, middle and end of a shift, on the same scale, and record the temperature at the same time. A filler that holds plus or minus 0.5 g at a steady 25 C may drift at 18 C. Acceptance without a temperature record is an argument waiting to happen.

Load cells designed specifically for liquids with high viscosity ensure consistent and reliable weight measurements, allowing you to maintain the quality standards of your product.

A different bottle format means a different unit; see the Filling Machine for Viscous Product.

How is an oil filler cleaned between products?

With a warm flush and a full drain, because oil does not rinse like water. The circuit needs a low point for drainage and a filter on the return. A change between two oils is quicker than a change from oil to a water-based product.

By prioritizing accurate weight measurement and addressing the unique challenges of high-viscosity liquids, managers and decision-makers can enhance the performance of their production lines and maintain consistent quality standards.

The same question is worked through from another angle in How to Select the Right Combibloc Filler for Edible.

How to read the numbers. Capacity figures come from the specification range, and the range is wide by design. Product temperature and viscosity shift the fill rate through a shift, so plan on 0.65-0.85 rather than the nameplate.

Frequently asked questions

Why does oil foam or bubble during filling?

Usually air entrained in the product or a fill that starts too fast. Letting the product settle in the bowl and ramping the valve opening removes most of it without changing the pump.

Does edible oil need nitrogen?

Some packers dose nitrogen into the headspace to slow oxidation, especially for polyunsaturated oils. It is an option, and its value depends on the oil and the target shelf life, not on the filler.

Can a load cell filler handle 5 L oil bottles?

Yes, with a longer fill time per valve. Above 2 L the practical rate per valve drops, so a 5 L line is normally specified for that format rather than shared with 1 L.

How is an oil line cleaned between products?

With a flushing cycle sized for the oil and the pipe run. High-viscosity oil needs a warm flush and a longer drain time than water, and the changeover belongs in the production plan.

Key takeaways
  1. Oil is sold by weight, so it is filled by weight.
  2. Acceptance needs a weight and a temperature recorded together.
  3. Weight, not volume, is the legal fill for oil.
  4. A temperature record turns an accuracy argument into a measurement.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.