How to Integrate Combibloc Fillers in Small Production Lines

Views: 1608 Author: Howie SUN Publish Time: Update Time:
The combiblock argument is floor space and labour, and the price is a shorter cushion between the blower and the filler when something stops.
Key facts at a glance
CombinesBlow moulding, filling and capping in one block
Capacity range2,000-48,000 BPH
Container range0.2-16 L PET
ProductsStill water, CSD, juice, tea, edible oil
ValvesLoad cell, volumetric, mechanical or semi-electric
OperationOne operator for the complete block

What does a combiblock actually combine?

A combiblock joins blow moulding, filling and capping into one frame with one drive and one control system. The preform goes in at one end and the capped bottle comes out at the other, with no intermediate buffer and no bottle storage between blowing and filling.

Where does a combiblock hurt when something stops?

Because there is no buffer, a stop at the blower reaches the filler in seconds. That is the trade: less floor space and less labour in exchange for less tolerance of short stops. The maintenance plan has to treat the blower and the filler as one unit, with one set of uptime targets.

ConfigurationWhat is insideTypical use
3-in-1 monoblockRinse, fill, capStill water in bought bottles
CombiblockBlow, fill, capPET lines with in-house blowing
Combiblock + labellerBlow, fill, cap, labelSingle-footprint PET line
Combiblock + packerBlow to caseHigh-volume single-format plant

For the same duty in another bottle format, the Still Water 5L Volumetric is specified separately.

How is output measured on a combiblock?

At the discharge of the block, in good capped bottles per hour, including the stops caused by blowing. Measuring at the filler alone flatters the number, because the filler waits for the blower more often than the other way round.

Valve count, utility schedule and footprint sit on the Blow-fill-cap Combibloc for Still Water page.

What maintenance does the blowing side need?

Oven lamp checks, mould cooling water quality and gripper alignment. The oven is the item that drifts quietly: a failing lamp changes the temperature profile and the bottle wall without stopping the machine.

The same question is worked through from another angle in What Is Blowing Filling Capping Combi For Water.

How to read the numbers. The output figures are specification ranges; the measured rate depends on the product and the shift. Because blowing, filling and capping share one frame, a stop anywhere stops the block. Plan on 0.65-0.85.

Frequently asked questions

What is the difference between a combiblock and a monoblock?

A monoblock combines rinsing, filling and capping. A combiblock adds blow moulding, so the preform goes in and the capped bottle comes out. The two terms are often confused, and the difference is whether a blow moulder is inside the block.

Why is there no bottle buffer in a combiblock?

The blower and the filler are mechanically linked, so bottles move directly from the mould to the filler. Removing the buffer saves space and dust exposure, but it also removes the cushion that absorbs short stops.

How much floor space does a combiblock save?

It removes the empty-bottle buffer and the conveyor between the blower and the filler, which is the largest space item on a conventional PET line. The exact saving depends on the buffer length in the original layout.

How is a combiblock cleaned?

Through a CIP circuit that covers the filler and the product path; the blowing side is cleaned separately as a dry section. The two cleaning regimes run on different schedules and should not be merged in the plan.

Key takeaways
  1. A combiblock trades buffer tolerance for floor space and labour.
  2. The valve follows the product; the block is only the frame.
  3. Foundation and levelling matter more because the machines are linked.
  4. The buffer is the space you save and the cushion you give up.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.