Hot Filling vs Cold Filling: Which Suits Juice?

Views: 9150 Author: Howie SUN Publish Time: Update Time:
Juice is a product-first decision: acidity, pulp and heat sensitivity choose the filling temperature, and the temperature chooses the bottle. Large cooling equipment is provided to cool the filled product to room temperature.

Hot Filling vs Cold Filling: Which Suits Juice?

Key facts at a glance
Filling principleHot-fill, up to 85 C
Capacity range6,000-36,000 BPH at 0.2-2 L
ContainerHeat-resistant PET geometry, or glass
LineHot-fill monobloc with tunnel pasteuriser
ProductsJuice, tea, nectar, functional drinks
Key controlFill temperature, hold time, cap seal

What breaks first on a hot-fill line?

Cap seals and filling valve O-rings, because they see the highest temperature every cycle. A seal that is fine on a water line at 20 C will harden in weeks at 85 C. The spare parts list should carry those two items in proportion to the number of valves, not as a single set.

When is cold filling the better route?

Cold filling protects heat-sensitive flavour and colour and allows a lighter bottle. It needs either a preservative system or a validated cold chain, and it moves the microbial control to the product and the plant rather than to the filler. The decision is commercial before it is technical.

RouteTemperatureWhat it costs
Hot fillUp to 85 CHeat-resistant bottle and a cooling tunnel
Cold fill with preservativeAmbientFormulation constraint, not a machine constraint
Cold fill with in-line pasteuriserProduct-side onlySeparate pasteuriser and a closed filling zone
Hot fill in glassUp to 85 CGlass mass, slower line, higher transport cost

Sizing for this duty runs through the Hotfill Type Filling Machine for Juice, where the valve count is set out.

Why does a hot-fill bottle need a cooling tunnel?

The bottle leaves the filler at up to 85 C and has to come down in a controlled ramp. A plunge cools the outside first, the inside contracts later, and the panel pulls in. The tunnel zones are set per bottle geometry and checked with a probe in the product.

Large cooling equipment is provided to cool the filled product to room temperature.

Throughput and change-part lists are on the Juice By Volumetric Filler page rather than in this note.

What does a glass juice line change?

Glass brings mass, breakage and a slower line. It also brings a closure decision: crown, lug or screw. A glass hot-fill line usually runs at a lower rate than the same filler on PET, and the difference is handling and inspection, not the valve.

The same question is worked through from another angle in Benefits of Using Piston Filling Machines for Juice with.

How to read the numbers. Treat the capacity figures as reference ranges from the product specification. Hot-fill lines lose time to heat-up and cooling that a rated BPH does not include; plan on 0.65-0.85.

Frequently asked questions

Does hot filling replace pasteurisation?

It replaces the bottle steriliser for acidic products, because the fill temperature and hold time do the microbial work. It does not replace correct product formulation or a validated hold tube.

Why does the bottle panel after filling?

Usually fill temperature above the bottle rating, or a vacuum that forms as the product cools. Check the fill temperature against the bottle specification and the cap seal before changing the cooling profile.

Can a hot-fill line run clear juice and pulp juice?

With a filter change and a different valve bore for the pulp, yes. Clear juice needs finer filtration, and pulp needs agitation in the bowl so the fibre does not settle.

What cooling profile does a hot-fill bottle need?

A controlled ramp rather than a cold plunge, so the bottle does not deform under vacuum. The tunnel zones are set per bottle geometry and validated with a temperature probe in the product.

Key takeaways
  1. Hot fill does pasteurisation and bottle sanitising in one step, and charges for it in bottle cost.
  2. Pulp needs bore and agitation, not more pressure.
  3. A change of fill temperature invalidates the shelf-life trial.
  4. Colour loss is a temperature and hold-time decision.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.