How to Select a Labeling Machine for Your Bottle Shape and Label Type

Views: 1830 Author: Howie SUN Publish Time: Update Time:
A labeller is the most frequent short stop on many lines, and the accumulator in front of it decides whether that stop reaches the filler.
Key facts at a glance
TypesSleeve, hot melt glue OPP, rotary sticker, self-adhesive
SpeedMatched to the filler, with an accumulator between
Key controlLabel position, glue pattern, shrinkage, adhesion
MaterialOPP film, PVC or PETG sleeve, paper sticker
Key decisionFull sleeve or partial wrap
Line positionAfter filling, before packing

Sleeve, OPP or sticker: what decides the choice?

A full-body sleeve covers the whole bottle and gives the most design freedom, at the cost of film and a shrink tunnel. An OPP wrap-around label is the cheapest per unit at high speed. A sticker suits short runs and curved surfaces where a wrap is impractical.

What does a shrink sleeve need to look right?

A consistent shrink needs the right film direction, a controlled tunnel temperature profile and a bottle that does not deform. Steam tunnels give a softer shrink than hot air and suit thin-wall bottles. A wrinkle at the shoulder is usually a film or temperature issue, not a speed issue.

Label typeCost per unitBest for
OPP wrap-aroundLowest at volumeHigh-speed round bottles
Full-body sleeveHigher film costFull coverage and shaped bottles
Self-adhesive stickerMiddleShort runs and flat or curved panels
Paper label with glueLow material, slowerGlass bottles and craft products

The unit behind this configuration is the Rotary Sticker Labeling.

Where does the labeller sit in the line?

After the filler and before the packer, normally with an accumulator on each side. The labeller is the most frequent short-stop on many lines, so the accumulator size in front of it decides whether a label roll change reaches the filler or not.

Throughput and change-part lists are on the Sleeve Labeling page rather than in this note.

What does a shrink sleeve need from the bottle design?

A consistent circumference and no sharp undercut where the film cannot follow. Sleeves shrink around the shape, so a bottle with a deep waist needs a film with the right shrink direction. The bottle and the sleeve are designed together.

The same question is worked through from another angle in How to Optimize Labeling for Multi-Size Bottles.

How to read the numbers. Rated capacity in this note follows the product specification range, not a factory acceptance test. Labelers lose rate to roll changes and glue build-up. Plan on a factor of 0.65-0.85 against the container rate.

Frequently asked questions

Why do labels wrinkle after shrinking?

Usually uneven tunnel temperature, wrong film orientation, or a bottle that is still warm from filling. Check the tunnel profile and the film direction before changing the speed.

Can one labeller run sleeve and OPP?

Not without a change of the applicator. Sleeve and wrap-around are different machines with different film paths, so a plant running both normally has two labellers.

What adhesive is used for OPP labels?

Hot melt glue applied at the leading edge, the trailing edge and the seam. The pattern and the pot temperature decide both the bond and how clean the bottle looks.

Why do labels lift at the seam?

Usually too little glue, a cold bottle, or a seam pressed before the glue sets. Check the glue pattern and the bottle temperature before changing the speed.

Key takeaways
  1. Label type is a cost-per-unit decision before it is a design decision.
  2. Position drift is a bottle handling problem, not a label problem.
  3. The accumulator in front of the labeller protects the filler.
  4. Perforation, tension and tunnel temperature act together.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.