How Gravity Filling Machines Handle Wine in Glass Bottles

Views: 2086 Author: Howie SUN Publish Time: Update Time:
Beer and wine are oxygen-sensitive products first and filling-speed problems second, so the filler is specified around dissolved oxygen and closure integrity. Similarly, the viscosity of the wine should be considered to ensure smooth and efficient filling without clogging or spillage.
Key facts at a glance
Filling principleIsobaric for beer, gravity or volumetric for wine and spirits
Capacity range4,000-20,000 BPH on glass
BottleGlass, 200-750 ml typical, crown or ROPP closure
Key controlDissolved oxygen, fill height, closure torque
Line scopeRinser, filler, capper or crowner, labeller, packer
CleaningCIP with caustic and rinse cycles

Why does beer need counter-pressure filling?

Beer carries dissolved CO2 and is extremely sensitive to oxygen. Counter-pressure filling keeps CO2 in solution and limits contact with air. The alternative, filling warm and flat, destroys the head and shortens shelf life. This is why a beer filler and a wine filler are rarely the same machine.

What does a small brewery actually need?

A small brewery usually needs a compact rinser-filler-crowner, a labeller and a packer that can run at 2,000-6,000 BPH, not a scaled-down version of a 24,000 BPH line. The constraint is changeover and cleaning time, because a small plant runs many products in short runs.

PackageFillingLine rate on glass
Glass bottle, crownIsobaric4,000-20,000 BPH
Glass bottle, ROPPIsobaric or gravity4,000-20,000 BPH
Aluminum canIsobaric + seamerUp to 25,000 CPH
PET, short shelf lifeIsobaricHigher rate, lower barrier

Throughput and change-part lists are on the Filling Machine for Glass CSD page rather than in this note.

What does a beer line need for foam control?

A cold fill, a controlled pressure release and a clean glass. Beer foams on the way into the bottle if the pressure drops too fast, and a foaming fill gives a short volume and a wet crown. The pressure ramp is the setting that matters.

Similarly, the viscosity of the wine should be considered to ensure smooth and efficient filling without clogging or spillage.

The Gravity Filling Machine for Glass Bottle Wine is the reference unit for this configuration.

How is a wine line different from a beer line?

Wine is usually filled still and often under inert gas, with a focus on oxygen and sulphite rather than CO2. Beer needs counter-pressure and foam control. The bottle handling is similar; the product protection is not.

The same question is worked through from another angle in Order for liquor bottling line from Tanzania.

How to read the numbers. Capacity figures come from the specification range, and the range is wide by design. Beer lines lose rate to foam control and CIP rather than to filler speed. Plan on a factor of 0.60-0.80.

Frequently asked questions

What is a normal dissolved oxygen target for beer?

The target is set by the brewery and the shelf life claim, and it is measured in the finished package. The line design should minimise pick-up at the filler and the closure; the exact limit belongs in the product specification.

Can a beer line fill both bottles and cans?

Only with two different fillers. Bottles are filled on an isobaric bottle filler with a crowner; cans on a can filler with a seamer. Some plants run both, but as two lines sharing utilities and packing.

Can a wine line run without a corker?

It needs a closure station matched to the closure: cork, screw cap or crown. The filler and the closure machine are specified together, because the bottle finish and the head are one decision.

Why does a glass line foam more than a PET line?

Glass surfaces and higher fill temperatures nucleate gas faster. The pressure ramp at the end of fill and the product temperature are the two settings that reduce it.

Key takeaways
  1. Beer is a dissolved-oxygen problem before it is a filling-speed problem.
  2. Each closure type needs its own capping head, not an adjustment.
  3. Closure type is chosen with the bottle, not after it.
  4. Glass lines carry inspection because breakage travels.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.