How Depalletizers Improve Workflow in Beverage Factories

Views: 1834 Author: Howie SUN Publish Time: Update Time:
The conveyor touches every bottle on the line, so guide rail gaps and transfer heights decide real uptime more than the filler rating does.
Key facts at a glance
What is includedAir conveyor, roller conveyor, depalletizer, palletizer
FunctionMove bottles and cases without damage, stack outbound pallets
Key controlAccumulation pressure, guide rail gap, pattern repeatability
TypesSemi-automatic and automatic palletizing
Key decisionManual, semi-automatic or robotic palletizing
AutomationManual, semi-automatic or robotic

When does automatic palletizing pay back?

Automatic palletizing pays when the labour it replaces is continuous and the pattern is stable. A plant running two shifts at high case rates reaches payback faster than a single-shift plant with mixed patterns, because a robot needs the pattern defined before it can be programmed.

What does a palletizer need from the building?

Floor loading for a full pallet stack, clear height for the mast or robot envelope, and a pallet dispenser within reach of the operator. These are building decisions taken before the machine is ordered, and changing them later costs more than the palletizer.

FunctionManualAutomatic
Depalletizing empty bottlesRack or hand stackLayer depalletizer
Case palletizingOperator with pattern sheetLayer or robotic palletizer
Pallet wrappingHand wrapperIn-line stretch wrapper
AccumulationNone, line stops togetherBuffer sized to longest stop

The specification sheet for the Depalletizing & Palletizing carries the figures quoted here.

How much accumulation is enough?

Enough to cover the longest normal downstream stop without stopping the filler. Beyond that, accumulation only hides the problem and adds floor space. The number comes from the stop-time log, not from a rule of thumb.

Reference unit for this duty: the Conveying.

What causes bottles to fall at transfers?

A guide rail gap set for a different diameter, a transfer plate at the wrong height, or too much back pressure behind the jam. All three are mechanical settings and all three drift when a second format is introduced.

The same question is worked through from another angle in How Depalletizers Improve Efficiency in Beverage Factories.

What does a depalletizer need from the bottle supplier?

Square pallets, consistent layer sheets and a stable stack. Empty bottles are light, so a leaning pallet becomes a fallen layer at the depalletizer. The machine can only work with the stack it is given.

How to read the numbers. Where a BPH appears below it is the specification range, not a measured rate. A rated pallet rate assumes one pattern and one layer; changeover sits outside it, so size on 0.65-0.85 of line speed.

Frequently asked questions

Why do bottles jam at conveyor transfers?

Guide rail gap and transfer plate height. Both are set for one bottle diameter and both drift when a second format is introduced. Re-set them at every changeover, not once at installation.

How many pallets per hour does an automatic palletizer handle?

It is rated in cycles per hour and depends on the layer pattern and the stack height. Compare the pattern-adjusted rate, not the headline figure.

Why does a depalletizer drop layers?

Low air pressure, a worn layer clamp, or a pallet that is not square. Empty bottle layers are light, so small errors become fallen bottles at the infeed.

What conveyor speed should a line use?

It follows the filler rate with margin for accumulation, not the maximum the conveyor can carry. Running a conveyor faster than the line needs increases scuffing and jam severity.

When is a semi-automatic palletizer the right choice?

When the pattern is stable and the labour is available at the end of the line. It costs less and runs slower, and it needs an operator for every layer change.

Key takeaways
  1. The conveyor touches every bottle, so it decides the real uptime.
  2. Accumulation should cover a normal stop, not hide a chronic one.
  3. Palletizing payback follows shift pattern and pattern stability.
  4. Empty-bottle layers punish a badly squared pallet.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.