Blow-Fill-Cap Labour Savings: Valve Choice and Output Measurement

Views: 1893 Author: Howie SUN Publish Time: Update Time:
The combiblock argument is floor space and labour, and the price is a shorter cushion between the blower and the filler when something stops.
Key facts at a glance
CombinesBlow moulding, filling and capping in one block
Capacity range2,000-48,000 BPH
Container range0.2-16 L PET
ProductsStill water, CSD, juice, tea, edible oil
ValvesLoad cell, volumetric, mechanical or semi-electric
OperationOne operator for the complete block

What does a combiblock actually combine?

A combiblock joins blow moulding, filling and capping into one frame with one drive and one control system. The preform goes in at one end and the capped bottle comes out at the other, with no intermediate buffer and no bottle storage between blowing and filling.

Which filling valve belongs in a combiblock?

The valve follows the product, not the block. Still water runs gravity or volumetric; oil runs load cell; CSD runs isobaric; juice runs hot fill or volumetric. The block is the frame, and the valve set is specified per product family, which is why one combiblock cannot simply switch between water and CSD.

ConfigurationWhat is insideTypical use
3-in-1 monoblockRinse, fill, capStill water in bought bottles
CombiblockBlow, fill, capPET lines with in-house blowing
Combiblock + labellerBlow, fill, cap, labelSingle-footprint PET line
Combiblock + packerBlow to caseHigh-volume single-format plant

Rated output, change parts and services are listed on the Blow-fill-cap Combibloc for CSD & Sparkling Water page.

How is output measured on a combiblock?

At the discharge of the block, in good capped bottles per hour, including the stops caused by blowing. Measuring at the filler alone flatters the number, because the filler waits for the blower more often than the other way round.

Where this becomes a line rather than a single machine, the Blow-fill-cap Combibloc for Still Water is the starting point.

What maintenance does the blowing side need?

Oven lamp checks, mould cooling water quality and gripper alignment. The oven is the item that drifts quietly: a failing lamp changes the temperature profile and the bottle wall without stopping the machine.

The same question is worked through from another angle in Advantages of Combining Filling and Capping in One Combibloc.

How to read the numbers. The capacity tab on the specification sheet gives ranges; treat them as such. Mould changes and the shared CIP cycle sit outside a rated BPH, so plan on 0.65-0.85.

Frequently asked questions

Does a combiblock save labour?

It is designed for one operator on the complete block, which is fewer people than three separate machines need. The saving is real only if the plant also removes the buffer and the bottle handling between stations.

Why is there no bottle buffer in a combiblock?

The blower and the filler are mechanically linked, so bottles move directly from the mould to the filler. Removing the buffer saves space and dust exposure, but it also removes the cushion that absorbs short stops.

What happens if the blower stops?

The filler stops within seconds because there is no accumulation. That is why the uptime target for a combiblock is set for the block, not for each machine, and why preventive maintenance on the blower is not optional.

Does a combiblock need a separate compressor?

It needs high-pressure air for blowing, which is usually a dedicated circuit. Sharing a low-pressure line with the rest of the plant is the most common cause of unstable bottle quality.

Key takeaways
  1. The valve follows the product; the block is only the frame.
  2. One uptime target for the block, not three for the machines.
  3. The buffer is the space you save and the cushion you give up.
  4. Blowing and filling keep separate cleaning regimes.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.