Combiblock Project Record: Contamination Control in Practice

Views: 1772 Author: Howie SUN Publish Time: Update Time:
A combiblock puts blow moulding, filling and capping on one frame with one control system, so the preform goes in and the capped bottle comes out.
Key facts at a glance
CombinesBlow moulding, filling and capping in one block
Capacity2,000-48,000 BPH
Format range0.2-16 L PET
ProductsStill water, CSD, juice, tea, edible oil
ValvesLoad cell, volumetric, mechanical or semi-electric
OperationOne operator for the complete block

What does a combiblock actually combine?

A combiblock joins blow moulding, filling and capping into one frame with one drive and one control system. The preform goes in at one end and the capped bottle comes out at the other, with no intermediate buffer and no bottle storage between blowing and filling.

Why does removing the buffer change the economics?

A conventional line stores empty bottles between the blower and the filler, and that buffer is floor space, conveyor, and a place where bottles collect dust. A combiblock removes all three, and because the three machines share one control system, one operator can run the block. The saving is in the building, not in the machine price.

ConfigurationWhat is insideTypical use
3-in-1 monoblockRinse, fill, capStill water in bought bottles
CombiblockBlow, fill, capPET lines with in-house blowing
Combiblock + labellerBlow, fill, cap, labelSingle-footprint PET line
Combiblock + packerBlow to caseHigh-volume single-format plant

For the same duty in another bottle format, the Blow-fill-cap Combibloc for CSD & Sparkling Water is specified separately.

Where does a combiblock hurt when something stops?

Because there is no buffer, a stop at the blower reaches the filler in seconds. That is the trade: less floor space and less labour in exchange for less tolerance of short stops. The maintenance plan has to treat the blower and the filler as one unit, with one set of uptime targets.

Rated output, change parts and services are listed on the Blow-fill-cap Combibloc for Still Water page.

Which filling valve belongs in a combiblock?

The valve follows the product, not the block. Still water runs gravity or volumetric; oil runs load cell; CSD runs isobaric; juice runs hot fill or volumetric. The block is the frame, and the valve set is specified per product family, which is why one combiblock cannot simply switch between water and CSD.

The same question is worked through from another angle in Blow-Fill-Cap Combiblock: 30,000 BPH on One Frame.

How to read the numbers. The capacity tab on the specification sheet gives ranges; treat them as such. Because blowing, filling and capping share one frame, a stop anywhere stops the block. Plan on 0.65-0.85.

Frequently asked questions

Can a combiblock run 500 ml and 5 L on the same day?

With change parts for the mould, the star wheels and the filling recipe, yes. The changeover is longer than on a filler alone because the mould set changes, and the production factor for a two-format week is lower than for a single format.

Why is there no bottle buffer in a combiblock?

The blower and the filler are mechanically linked, so bottles move directly from the mould to the filler. Removing the buffer saves space and dust exposure, but it also removes the cushion that absorbs short stops.

How much floor space does a combiblock save?

It removes the empty-bottle buffer and the conveyor between the blower and the filler, which is the largest space item on a conventional PET line. The exact saving depends on the buffer length in the original layout.

Does a combiblock need a separate compressor?

It needs high-pressure air for blowing, which is usually a dedicated circuit. Sharing a low-pressure line with the rest of the plant is the most common cause of unstable bottle quality.

Key takeaways
  1. A combiblock trades buffer tolerance for floor space and labour.
  2. One uptime target for the block, not three for the machines.
  3. The buffer is the space you save and the cushion you give up.
  4. Blowing and filling keep separate cleaning regimes.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.