The Role of Volumetric Fillers in High-Speed Juice Bottling

Views: 1645 Author: Howie SUN Publish Time: Update Time:
Hot filling pasteurises the product and sanitises the bottle in one pass, which is why acidic juice and tea can be filled without a separate bottle steriliser.
Key facts at a glance
Filling systemHot-fill, up to 85 C
Output range6,000-36,000 BPH at 0.2-2 L
BottleHeat-resistant PET geometry, or glass
LineHot-fill monobloc with tunnel pasteuriser
ProductsJuice, tea, nectar, functional drinks
Key controlFill temperature, hold time, cap seal

What does the fill temperature actually control?

Fill temperature and hold time together set the pasteurisation result. Below the target, shelf life is at risk; above it, the product cooks and the bottle deforms. The number belongs to the product and the bottle, not to the machine, and it should be written into the acceptance protocol with a tolerance.

What breaks first on a hot-fill line?

Cap seals and filling valve O-rings, because they see the highest temperature every cycle. A seal that is fine on a water line at 20 C will harden in weeks at 85 C. The spare parts list should carry those two items in proportion to the number of valves, not as a single set.

RouteTemperatureWhat it costs
Hot fillUp to 85 CHeat-resistant bottle and a cooling tunnel
Cold fill with preservativeAmbientFormulation constraint, not a machine constraint
Cold fill with in-line pasteuriserProduct-side onlySeparate pasteuriser and a closed filling zone
Hot fill in glassUp to 85 CGlass mass, slower line, higher transport cost

The unit behind this configuration is the Juice By Volumetric Filler.

How do you compare a hot-fill line with a cold-fill line?

Compare them on the product, not on the machine. Hot fill suits acidic juice and tea in heat-resistant PET. Cold fill needs a preservative system or a separate sanitising step, but it protects heat-sensitive flavours and vitamins and uses a lighter bottle. The decision is a product decision with a packaging cost attached.

Site requirements, air and water consumption sit with the Hotfill Type Filling Machine for Juice.

When is cold filling the better route?

Cold filling protects heat-sensitive flavour and colour and allows a lighter bottle. It needs either a preservative system or a validated cold chain, and it moves the microbial control to the product and the plant rather than to the filler. The decision is commercial before it is technical.

The same question is worked through from another angle in Understanding Hotfill vs Coldfill Processes.

What does a tea line need that a juice line does not?

Tea usually needs finer filtration, deaeration to protect aroma, and a fill temperature that does not strip the volatile notes. Tea also clouds after cooling, so the clarification step is part of the product design, not a filling detail.

How to read the numbers. Capacity figures come from the specification range, and the range is wide by design. Hot-fill lines lose time to heat-up and cooling that a rated BPH does not include; plan on 0.65-0.85.

Frequently asked questions

What temperature is juice hot-filled at?

Up to 85 C, set per product and per bottle. The exact set point and tolerance belong in the product specification, because acidity, pulp content and bottle wall thickness all move it.

Does hot filling replace pasteurisation?

It replaces the bottle steriliser for acidic products, because the fill temperature and hold time do the microbial work. It does not replace correct product formulation or a validated hold tube.

How long does a hot-fill line take to reach temperature?

It depends on the hold tube volume and the heater capacity. The line is not production-ready until the return temperature is stable, so start-up time belongs in the daily plan rather than being discovered at shift start.

Why does juice lose colour after hot filling?

Heat-sensitive pigments and vitamins degrade above the product temperature limit. The fill temperature and the hold time are the two variables; lowering either protects colour and shortens the microbial margin.

Can a hot-fill line run clear juice and pulp juice?

With a filter change and a different valve bore for the pulp, yes. Clear juice needs finer filtration, and pulp needs agitation in the bowl so the fibre does not settle.

Key takeaways
  1. Hot fill does pasteurisation and bottle sanitising in one step, and charges for it in bottle cost.
  2. Pulp needs bore and agitation, not more pressure.
  3. Cold filling moves the microbial control from the filler to the product and the plant.
  4. Colour loss is a temperature and hold-time decision.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.