Depalletizers and Palletizers: Automating Your Bottling Line's Start and Finish

Views: 1842 Author: Howie SUN Publish Time: Update Time:
Palletizing payback follows shift pattern and pattern stability, not the price of the robot.
Key facts at a glance
What is includedAir conveyor, roller conveyor, depalletizer, palletizer
FunctionMove bottles and cases without damage, stack outbound pallets
Key controlAccumulation pressure, guide rail gap, pattern repeatability
TypesSemi-automatic and automatic palletizing
Key decisionManual, semi-automatic or robotic palletizing
AutomationManual, semi-automatic or robotic

What breaks at the depalletizer?

Empty bottle layers are light and unstable, so the depalletizer is where a badly stacked pallet becomes a line stop. Layer pickup, sweep speed and the interface with the air conveyor are the three settings to check, and the pallet quality from the bottle supplier matters as much as the machine.

What does a palletizer need from the building?

Floor loading for a full pallet stack, clear height for the mast or robot envelope, and a pallet dispenser within reach of the operator. These are building decisions taken before the machine is ordered, and changing them later costs more than the palletizer.

FunctionManualAutomatic
Depalletizing empty bottlesRack or hand stackLayer depalletizer
Case palletizingOperator with pattern sheetLayer or robotic palletizer
Pallet wrappingHand wrapperIn-line stretch wrapper
AccumulationNone, line stops togetherBuffer sized to longest stop

The unit behind this configuration is the Depalletizing & Palletizing.

What causes bottles to fall at transfers?

A guide rail gap set for a different diameter, a transfer plate at the wrong height, or too much back pressure behind the jam. All three are mechanical settings and all three drift when a second format is introduced.

Site requirements, air and power consumption sit with the Conveying.

When does a robotic palletizer beat a layer palletizer?

When the pattern mix is wide and the pack is fragile. A layer palletizer is faster on one stable pattern; a robot changes pattern by program. Most plants with more than three patterns choose the robot for that reason alone.

The same question is worked through from another angle in How to Handle and Solve Common Conveyor System Jams.

What does a depalletizer need from the bottle supplier?

Square pallets, consistent layer sheets and a stable stack. Empty bottles are light, so a leaning pallet becomes a fallen layer at the depalletizer. The machine can only work with the stack it is given.

How to read the numbers. Where a BPH appears below it is the specification range, not a measured rate. Conveyor accumulation hides short stops but not pattern changes. Plan on a factor of 0.65-0.85.

Frequently asked questions

How many cases per hour can a palletizer handle?

It is rated in cases or layers per hour and must exceed the packer output with margin. The number to compare is the pattern-adjusted rate, not the headline figure at one layer size.

What is the difference between a depalletizer and a palletizer?

A depalletizer unloads empty bottles or full cases from a pallet at the start of a line. A palletizer stacks finished cases onto a pallet at the end. They are separate machines with separate footprints.

Why do bottles jam at conveyor transfers?

Guide rail gap and transfer plate height. Both are set for one bottle diameter and both drift when a second format is introduced. Re-set them at every changeover, not once at installation.

How many pallets per hour does an automatic palletizer handle?

It is rated in cycles per hour and depends on the layer pattern and the stack height. Compare the pattern-adjusted rate, not the headline figure.

Why does a depalletizer drop layers?

Low air pressure, a worn layer clamp, or a pallet that is not square. Empty bottle layers are light, so small errors become fallen bottles at the infeed.

Key takeaways
  1. The conveyor touches every bottle, so it decides the real uptime.
  2. Accumulation should cover a normal stop, not hide a chronic one.
  3. Guide rail gap is a per-format setting, not an installation setting.
  4. Compare the pattern-adjusted palletizer rate, not the headline.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.