Benefits of Volumetric Hotfill Machines for Glass Bottles

Views: 1611 Author: Howie SUN Publish Time: Update Time:
A juice line that runs at the right temperature holds shelf life; one that runs hot enough to deform the bottle trades shelf life for rejects. One of the key challenges in hot filling glass bottles is the potential for thermal shock and breakage due to the high temperatures involved in the process.
Key facts at a glance
Valve typeHot-fill, up to 85 C
Capacity6,000-36,000 BPH at 0.2-2 L
BottleHeat-resistant PET geometry, or glass
LineHot-fill monobloc with tunnel pasteuriser
ProductsJuice, tea, nectar, functional drinks
Key controlFill temperature, hold time, cap seal

How do you keep pulp and fibre moving through the line?

Pulp needs either a larger valve bore or a piston filler, and it needs continuous gentle agitation in the bowl. Dead corners in the product path settle fibre, then release it as a slug into the next bottle. Bowl geometry and return-flow design matter more than valve count here.

How do you compare a hot-fill line with a cold-fill line?

Compare them on the product, not on the machine. Hot fill suits acidic juice and tea in heat-resistant PET. Cold fill needs a preservative system or a separate sanitising step, but it protects heat-sensitive flavours and vitamins and uses a lighter bottle. The decision is a product decision with a packaging cost attached.

RouteTemperatureWhat it costs
Hot fillUp to 85 CHeat-resistant bottle and a cooling tunnel
Cold fill with preservativeAmbientFormulation constraint, not a machine constraint
Cold fill with in-line pasteuriserProduct-side onlySeparate pasteuriser and a closed filling zone
Hot fill in glassUp to 85 CGlass mass, slower line, higher transport cost

The unit behind this configuration is the Hotfill Type Filling Machine for Juice.

When is cold filling the better route?

Cold filling protects heat-sensitive flavour and colour and allows a lighter bottle. It needs either a preservative system or a validated cold chain, and it moves the microbial control to the product and the plant rather than to the filler. The decision is commercial before it is technical.

Valve count, utility schedule and footprint sit on the Juice By Volumetric Filler page.

What does a glass juice line change?

Glass brings mass, breakage and a slower line. It also brings a closure decision: crown, lug or screw. A glass hot-fill line usually runs at a lower rate than the same filler on PET, and the difference is handling and inspection, not the valve.

One of the key challenges in hot filling glass bottles is the potential for thermal shock and breakage due to the high temperatures involved in the process.

The same question is worked through from another angle in How Combibloc Fillers Improve Efficiency in Juice Production.

How to read the numbers. Capacity figures are the reference ranges on the product specification. A rated BPH covers filling only. Pasteurisation, hold time and cooling sit outside it, so size on 0.65-0.85.

Frequently asked questions

Does hot filling replace pasteurisation?

It replaces the bottle steriliser for acidic products, because the fill temperature and hold time do the microbial work. It does not replace correct product formulation or a validated hold tube.

How long does a hot-fill line take to reach temperature?

It depends on the hold tube volume and the heater capacity. The line is not production-ready until the return temperature is stable, so start-up time belongs in the daily plan rather than being discovered at shift start.

Why does juice lose colour after hot filling?

Heat-sensitive pigments and vitamins degrade above the product temperature limit. The fill temperature and the hold time are the two variables; lowering either protects colour and shortens the microbial margin.

What cooling profile does a hot-fill bottle need?

A controlled ramp rather than a cold plunge, so the bottle does not deform under vacuum. The tunnel zones are set per bottle geometry and validated with a temperature probe in the product.

Key takeaways
  1. Fill temperature is a product and package number, not a machine setting.
  2. Pulp needs bore and agitation, not more pressure.
  3. Cold filling moves the microbial control from the filler to the product and the plant.
  4. Colour loss is a temperature and hold-time decision.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.