A Guide to Key International Certifications for Filling Machinery (CE, ISO, FDA)

Views: 2312 Author: Howie SUN Publish Time: Update Time:
A filling machine is specified from the product and the package, and every other number follows: viscosity and carbonation pick the valve, the neck finish picks the capper. ISO certification, particularly ISO 9001 and ISO 22000, focuses on quality management and food safety management systems, respectively.
Key facts at a glance
What is includedFilling, capping and closing equipment
Filling principlesGravity, volumetric, isobaric, piston, load cell
Capacity range2,000-48,000 BPH by configuration
Accuracy basisVolume, weight or fill level
Contact materialSUS 304 product contact, CIP-ready
Key controlFill accuracy, closure integrity, CIP time

Which filling principle fits this product?

The product fixes the filling principle; output only fixes the size. Still liquid at a steady density runs gravity or volumetric; carbonated product needs isobaric; thick product with solids needs a piston; product sold by weight runs a load cell. A machine picked ahead of the product usually gets picked again.

What actually decides fill accuracy?

Four variables sit behind a fill number: the dosing principle, the product temperature, the bottle geometry, and the condition of the valve or piston seal. A machine that holds its tolerance on the factory test can drift in the plant when the product arrives warmer or the bottle wall gets thinner.

PrincipleDoses byFails when
GravityFill level in the bottleBottle geometry varies
VolumetricChamber volumeValve seal wears
IsobaricVolume under counter-pressurePressure or temperature drifts
PistonDisplacementProduct carries solids
Load cellNet weightProduct temperature moves

For the same duty in another bottle format, the Gravity Filling Machine for Still Water is specified separately.

What should the acceptance test measure?

Rated output at the specified format, fill accuracy on a defined sample, closure torque or seal measurement, and a timed changeover with the buyer watching. Anything not measured before sign-off becomes a discussion after the final payment.

ISO certification, particularly ISO 9001 and ISO 22000, focuses on quality management and food safety management systems, respectively.

Rated output, change parts and services are listed on the Volumetric Filling Machine for Still Water page.

How does the bottle neck finish change the machine?

The neck finish sets the rinser clamp, the filling valve seal and the capping head. A change of a millimetre in the thread is a change of change parts and often of the capper. It is the single most under-specified item in a filling line enquiry.

The same question is worked through from another angle in How Much Does a Beverage Filling Line Cost? Complete.

How to read the numbers. Capacity figures come from the specification range, and the range is wide by design. A rated BPH is one format at steady state. Changeover, CIP and downstream stops sit outside it, so size on 0.65-0.85.

Frequently asked questions

How accurate is a filling machine?

It depends on the principle and the product. A volumetric or load cell filler holds a tighter band than gravity on a variable bottle. The tolerance belongs in the acceptance protocol, measured by weight on a defined sample.

Can one filler run different bottle sizes?

Yes, with change parts: star wheels, guide rails, grippers and a recipe. The parts are cheap compared with the changeover time, which is why most plants specify one dominant format.

What spare parts should be kept in stock?

Valve seals, piston seals, capping head inserts, guide rail blocks and one set of change parts for the second format. These are the items that stop a line for days when they fail.

What is the difference between rated BPH and real output?

Rated BPH is a steady-state figure at one format. Real output subtracts changeover, CIP, label changes and downstream stops, which is why planning uses a factor of 0.65-0.85.

Key takeaways
  1. The product picks the filling principle; the output only picks the size.
  2. Fill accuracy is a temperature and wear question as much as a machine question.
  3. Each closure family needs its own capping head.
  4. CIP is downtime; it belongs in the capacity plan, not in the maintenance schedule alone.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.