What Is the Juice Filling Machine Used for?

Views: 4544 Author: Howie SUN Publish Time: Update Time:
Juice is a product-first decision: acidity, pulp and heat sensitivity choose the filling temperature, and the temperature chooses the bottle.
Key facts at a glance
Valve typeHot-fill, up to 85 C
Capacity range6,000-36,000 BPH at 0.2-2 L
BottleHeat-resistant PET geometry, or glass
LineHot-fill monobloc with tunnel pasteuriser
ProductsJuice, tea, nectar, functional drinks
Key controlFill temperature, hold time, cap seal

Why does juice get filled hot instead of cold?

Hot filling does two jobs at once: it pasteurises the product on the way to the filler, and the residual heat sanitises the bottle and cap. That is why a hot-fill line can run an acidic juice without a separate bottle steriliser. The price is a heat-resistant bottle and a longer cooling tunnel.

How do you compare a hot-fill line with a cold-fill line?

Compare them on the product, not on the machine. Hot fill suits acidic juice and tea in heat-resistant PET. Cold fill needs a preservative system or a separate sanitising step, but it protects heat-sensitive flavours and vitamins and uses a lighter bottle. The decision is a product decision with a packaging cost attached.

RouteTemperatureWhat it costs
Hot fillUp to 85 CHeat-resistant bottle and a cooling tunnel
Cold fill with preservativeAmbientFormulation constraint, not a machine constraint
Cold fill with in-line pasteuriserProduct-side onlySeparate pasteuriser and a closed filling zone
Hot fill in glassUp to 85 CGlass mass, slower line, higher transport cost

The Juice By Volumetric Filler is the matching unit when this becomes a line project.

What does a tea line need that a juice line does not?

Tea usually needs finer filtration, deaeration to protect aroma, and a fill temperature that does not strip the volatile notes. Tea also clouds after cooling, so the clarification step is part of the product design, not a filling detail.

The specification sheet for the Hotfill Type Filling Machine for Juice carries the utility figures quoted here.

What does a glass juice line change?

Glass brings mass, breakage and a slower line. It also brings a closure decision: crown, lug or screw. A glass hot-fill line usually runs at a lower rate than the same filler on PET, and the difference is handling and inspection, not the valve.

The same question is worked through from another angle in How Hotfill Juice Lines Improve Shelf Life in Retail.

How to read the numbers. Capacity on these pages means the specification range, before any site-specific derating. Hot-fill lines lose time to heat-up and cooling that a rated BPH does not include; plan on 0.65-0.85.

Frequently asked questions

Can hot-fill juice run in standard PET bottles?

No. Standard PET softens and deforms at fill temperature. The bottle needs a heat-resistant geometry, and the mould and preform are part of the project, not an afterthought.

Can one line run juice and tea?

Yes, if the filler, the recipe and the downstream cooling are specified for both. Tea usually needs a finer filtration step and a different deaeration setting, so the changeover is a recipe and filter change, not just a new label.

Can a hot-fill line run clear juice and pulp juice?

With a filter change and a different valve bore for the pulp, yes. Clear juice needs finer filtration, and pulp needs agitation in the bowl so the fibre does not settle.

What cooling profile does a hot-fill bottle need?

A controlled ramp rather than a cold plunge, so the bottle does not deform under vacuum. The tunnel zones are set per bottle geometry and validated with a temperature probe in the product.

Key takeaways
  1. Hot fill does pasteurisation and bottle sanitising in one step, and charges for it in bottle cost.
  2. Cold filling moves the microbial control from the filler to the product and the plant.
  3. A change of fill temperature invalidates the shelf-life trial.
  4. Cool the bottle on a ramp, not a plunge.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.