Volumetric Juice Filling Accuracy: Fill Temperature and Tea Lines

Views: 1648 Author: Howie SUN Publish Time: Update Time:
Hot filling pasteurises the product and sanitises the bottle in one pass, which is why acidic juice and tea can be filled without a separate bottle steriliser. Unlike weight-based systems that rely on gravity and can be influenced by factors such as product temperature and density, volumetric fillers operate with precision regardless of these variables.
Key facts at a glance
Filling methodHot-fill, up to 85 C
Capacity6,000-36,000 BPH at 0.2-2 L
BottleHeat-resistant PET geometry, or glass
LineHot-fill monobloc with tunnel pasteuriser
ProductsJuice, tea, nectar, functional drinks
Key controlFill temperature, hold time, cap seal

What does the fill temperature actually control?

Fill temperature and hold time together set the pasteurisation result. Below the target, shelf life is at risk; above it, the product cooks and the bottle deforms. The number belongs to the product and the bottle, not to the machine, and it should be written into the acceptance protocol with a tolerance.

Unlike weight-based systems that rely on gravity and can be influenced by factors such as product temperature and density, volumetric fillers operate with precision regardless of these variables.

How do you keep pulp and fibre moving through the line?

Pulp needs either a larger valve bore or a piston filler, and it needs continuous gentle agitation in the bowl. Dead corners in the product path settle fibre, then release it as a slug into the next bottle. Bowl geometry and return-flow design matter more than valve count here.

RouteTemperatureWhat it costs
Hot fillUp to 85 CHeat-resistant bottle and a cooling tunnel
Cold fill with preservativeAmbientFormulation constraint, not a machine constraint
Cold fill with in-line pasteuriserProduct-side onlySeparate pasteuriser and a closed filling zone
Hot fill in glassUp to 85 CGlass mass, slower line, higher transport cost

Site requirements, air and water consumption sit with the Juice By Volumetric Filler.

What does a tea line need that a juice line does not?

Tea usually needs finer filtration, deaeration to protect aroma, and a fill temperature that does not strip the volatile notes. Tea also clouds after cooling, so the clarification step is part of the product design, not a filling detail.

The specification sheet for the Hotfill Type Filling Machine for Juice carries the utility figures quoted here.

How does pulp size affect the filler choice?

Pulp decides the bore and the valve seat, and it decides whether a piston is needed. A filler set for clear juice bridges on pulp and the dose falls short. Specify the largest particle in the product before the machine is quoted.

The same question is worked through from another angle in How to Optimize Hotfill Juice Filling Lines for Efficiency.

How to read the numbers. Capacity figures are the reference ranges on the product specification. A rated BPH covers filling only. Pasteurisation, hold time and cooling sit outside it, so size on 0.65-0.85.

Frequently asked questions

Can hot-fill juice run in standard PET bottles?

No. Standard PET softens and deforms at fill temperature. The bottle needs a heat-resistant geometry, and the mould and preform are part of the project, not an afterthought.

Why does the bottle panel after filling?

Usually fill temperature above the bottle rating, or a vacuum that forms as the product cools. Check the fill temperature against the bottle specification and the cap seal before changing the cooling profile.

Can one line run juice and tea?

Yes, if the filler, the recipe and the downstream cooling are specified for both. Tea usually needs a finer filtration step and a different deaeration setting, so the changeover is a recipe and filter change, not just a new label.

Can a hot-fill line run clear juice and pulp juice?

With a filter change and a different valve bore for the pulp, yes. Clear juice needs finer filtration, and pulp needs agitation in the bowl so the fibre does not settle.

Key takeaways
  1. Fill temperature is a product and package number, not a machine setting.
  2. Pulp needs bore and agitation, not more pressure.
  3. Cold filling moves the microbial control from the filler to the product and the plant.
  4. Cool the bottle on a ramp, not a plunge.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.