Gravity Filling Machines for Glass Bottle Juice and Tea Drinks

Views: 1614 Author: Howie SUN Publish Time: Update Time:
Hot filling pasteurises the product and sanitises the bottle in one pass, which is why acidic juice and tea can be filled without a separate bottle steriliser. Glass bottles are prone to breakage under pressure, making the gentle gravity filling process a safer and more appropriate option.
Key facts at a glance
Filling methodHot-fill, up to 85 C
Capacity range6,000-36,000 BPH at 0.2-2 L
PackageHeat-resistant PET geometry, or glass
LineHot-fill monobloc with tunnel pasteuriser
ProductsJuice, tea, nectar, functional drinks
Key controlFill temperature, hold time, cap seal

How do you keep pulp and fibre moving through the line?

Pulp needs either a larger valve bore or a piston filler, and it needs continuous gentle agitation in the bowl. Dead corners in the product path settle fibre, then release it as a slug into the next bottle. Bowl geometry and return-flow design matter more than valve count here.

What does a tea line need that a juice line does not?

Tea usually needs finer filtration, deaeration to protect aroma, and a fill temperature that does not strip the volatile notes. Tea also clouds after cooling, so the clarification step is part of the product design, not a filling detail.

RouteTemperatureWhat it costs
Hot fillUp to 85 CHeat-resistant bottle and a cooling tunnel
Cold fill with preservativeAmbientFormulation constraint, not a machine constraint
Cold fill with in-line pasteuriserProduct-side onlySeparate pasteuriser and a closed filling zone
Hot fill in glassUp to 85 CGlass mass, slower line, higher transport cost

The Aluminum Can Filling Machine for Hotfill Juice and Tea is the matching unit when this becomes a line project.

What does a glass juice line change?

Glass brings mass, breakage and a slower line. It also brings a closure decision: crown, lug or screw. A glass hot-fill line usually runs at a lower rate than the same filler on PET, and the difference is handling and inspection, not the valve.

Glass bottles are prone to breakage under pressure, making the gentle gravity filling process a safer and more appropriate option.

Where this becomes a line rather than a single machine, the Hotfill Type Filling Machine for Juice is the starting point.

How is shelf life validated after a change?

With a storage trial on the actual product, bottle and closure, held at the intended temperature and sampled on a schedule. Changing the fill temperature, the bottle or the cap invalidates the previous result, which is why those three are treated as one specification.

The same question is worked through from another angle in How Gravity Fillers Handle Wine and Juice Lines.

How to read the numbers. Capacity figures are the reference ranges on the product specification. A rated BPH covers filling only. Pasteurisation, hold time and cooling sit outside it, so size on 0.65-0.85.

Frequently asked questions

Does hot filling replace pasteurisation?

It replaces the bottle steriliser for acidic products, because the fill temperature and hold time do the microbial work. It does not replace correct product formulation or a validated hold tube.

How long does a hot-fill line take to reach temperature?

It depends on the hold tube volume and the heater capacity. The line is not production-ready until the return temperature is stable, so start-up time belongs in the daily plan rather than being discovered at shift start.

Can one line run juice and tea?

Yes, if the filler, the recipe and the downstream cooling are specified for both. Tea usually needs a finer filtration step and a different deaeration setting, so the changeover is a recipe and filter change, not just a new label.

Why does juice lose colour after hot filling?

Heat-sensitive pigments and vitamins degrade above the product temperature limit. The fill temperature and the hold time are the two variables; lowering either protects colour and shortens the microbial margin.

Key takeaways
  1. Fill temperature is a product and package number, not a machine setting.
  2. Cap seals and valve O-rings are the first wear items on a hot line.
  3. Colour loss is a temperature and hold-time decision.
  4. Cool the bottle on a ramp, not a plunge.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.