How to Select the Right Load Cell Combibloc

Views: 1850 Author: Howie SUN Publish Time: Update Time:
A combiblock puts blow moulding, filling and capping on one frame with one control system, so the preform goes in and the capped bottle comes out.
Key facts at a glance
CombinesBlow moulding, filling and capping in one block
Capacity2,000-48,000 BPH
Bottle sizes0.2-16 L PET
ProductsStill water, CSD, juice, tea, edible oil
ValvesLoad cell, volumetric, mechanical or semi-electric
OperationOne operator for the complete block

What does a combiblock actually combine?

A combiblock joins blow moulding, filling and capping into one frame with one drive and one control system. The preform goes in at one end and the capped bottle comes out at the other, with no intermediate buffer and no bottle storage between blowing and filling.

Why does removing the buffer change the economics?

A conventional line stores empty bottles between the blower and the filler, and that buffer is floor space, conveyor, and a place where bottles collect dust. A combiblock removes all three, and because the three machines share one control system, one operator can run the block. The saving is in the building, not in the machine price.

ConfigurationWhat is insideTypical use
3-in-1 monoblockRinse, fill, capStill water in bought bottles
CombiblockBlow, fill, capPET lines with in-house blowing
Combiblock + labellerBlow, fill, cap, labelSingle-footprint PET line
Combiblock + packerBlow to caseHigh-volume single-format plant

Valve count, utility schedule and footprint sit on the Still Water 5L Volumetric page.

What does a combiblock need from the building?

A single footprint, a level floor, high-pressure air for blowing, chilled water for the mould, and power for the whole block on one feed. Because the machines are mechanically linked, the foundation and the levelling matter more than on three separate machines, and the installation sequence is fixed.

Where this becomes a line rather than a single machine, the Blow-fill-cap Combibloc for Still Water is the starting point.

How is output measured on a combiblock?

At the discharge of the block, in good capped bottles per hour, including the stops caused by blowing. Measuring at the filler alone flatters the number, because the filler waits for the blower more often than the other way round.

The same question is worked through from another angle in How Blow-Fill-Cap Machines Improve Bottled Water Safety.

How to read the numbers. Rated capacity in this note follows the product specification range, not a factory acceptance test. A combiblock rating assumes one preform and one cap; mould change and CIP sit outside it, so size on 0.65-0.85.

Frequently asked questions

Can a combiblock run 500 ml and 5 L on the same day?

With change parts for the mould, the star wheels and the filling recipe, yes. The changeover is longer than on a filler alone because the mould set changes, and the production factor for a two-format week is lower than for a single format.

What happens if the blower stops?

The filler stops within seconds because there is no accumulation. That is why the uptime target for a combiblock is set for the block, not for each machine, and why preventive maintenance on the blower is not optional.

How is a combiblock cleaned?

Through a CIP circuit that covers the filler and the product path; the blowing side is cleaned separately as a dry section. The two cleaning regimes run on different schedules and should not be merged in the plan.

Does a combiblock need a separate compressor?

It needs high-pressure air for blowing, which is usually a dedicated circuit. Sharing a low-pressure line with the rest of the plant is the most common cause of unstable bottle quality.

Key takeaways
  1. One uptime target for the block, not three for the machines.
  2. Foundation and levelling matter more because the machines are linked.
  3. The buffer is the space you save and the cushion you give up.
  4. Blowing and filling keep separate cleaning regimes.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.