How Semi-Electric Fillers Optimize CSD Production Lines

Views: 1502 Author: Howie SUN Publish Time: Update Time:
Isobaric filling is the only way to put a carbonated drink into a bottle without losing the gas, which is why a still water filler cannot be converted by adding a CO2 unit.
Key facts at a glance
Filling methodIsobaric, CO2 counter-pressure
Output range12,000-36,000 BPH at 0.2-2 L
ContainersPET bottle, glass bottle, aluminum can
CO2 handlingPre-pressurisation and return pipe, no venting
ValvesMechanical, semi-electric or volumetric
Line scopeWater treatment, syrup mixing, carbonation, filler, pack

Why does carbonated product need isobaric filling?

A carbonated drink is a saturated solution held in equilibrium by pressure and temperature. If the filler exposes it to atmosphere, CO2 leaves the liquid as foam and the fill level collapses. Isobaric filling pressurises the bottle to the bowl pressure first, fills under counter-pressure, then releases in a controlled ramp.

What decides CO2 retention on the line?

Four points decide it: the carbonation level set at the mixer, the product temperature at the filler, the pressure profile during fill, and the time between capping and packing. A line that holds 4.0 volumes at the mixer can deliver 3.4 in the bottle if the filler bowl runs warm or the capping head leaks.

Valve typeSettingBest for
MechanicalFixed cam profileSingle product, long runs
Semi-electricSignal-timed open and closeRecipe changes within one product family
VolumetricChamber dosePressure or temperature drift during the shift
Isobaric + volumetricChamber dose under counter-pressureHigh CO2 with tight fill accuracy

A different bottle format means a different unit; see the CSD & Sparkling Water by Mechanical Filler.

How do you size a CSD line without oversizing the CO2 plant?

Size the filler on peak shift demand with a production factor of 0.65-0.85, then size the CO2 supply on average consumption, not peak. A CO2 plant built for the filler nameplate runs partly loaded for most of the year and loses more gas to vaporisation than the line saves in speed.

Throughput and change-part lists are on the Isobaric Filling Machine for CSD and Sparkling Water page rather than in this note.

How is syrup mixed and carbonated before the filler?

Syrup is proportioned and blended with treated water, then carbonated under pressure and temperature control. The ratio accuracy and the carbonation stability decide the product, and both are upstream of the filler. A filler cannot correct a drifting blend.

The same question is worked through from another angle in How to Choose Between Volumetric and Mechanical Fillers for.

How to read the numbers. Rated capacity in this note follows the product specification range, not a factory acceptance test. A rated BPH is measured at one CO2 level and one temperature; format changes and CIP sit outside it, so size on 0.65-0.85.

Frequently asked questions

What CO2 level can an isobaric filler hold?

It holds what the mixer sets and the temperature allows. Most CSD runs between 2.5 and 4.0 volumes, with the target set per product. Retention, not the mixer set point, is what the acceptance test should measure in the filled bottle.

How many cans per hour is 24,000 CPH?

400 cans per minute. CPH and BPH are different units and cannot be compared directly, because can and bottle formats carry different volumes and different downstream equipment.

Does a CSD line need a nitrogen doser?

It is used where the package needs internal pressure support or low oxygen, for example in cans and in some PET formats. It is an option, not a default, and it adds a consumable cost per 1,000 units.

Can a CSD line fill glass bottles?

Yes, with a different infeed, spacing and capping set. Glass needs mechanical spacing rather than an air conveyor, and the filler runs at 4,000-20,000 BPH on glass against 12,000-36,000 BPH on PET.

Key takeaways
  1. Carbonation is a pressure and temperature problem before it is a valve problem.
  2. Judge a CSD line on CO2 retention in the filled bottle, not on the mixer set point.
  3. Size the CO2 plant on average demand, not on the filler nameplate.
  4. Warm product loses CO2 before the filler can dose it.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.