How Gravity Fillers Handle Delicate Liquids Like Wine

Views: 2053 Author: Howie SUN Publish Time: Update Time:
Beer and wine are oxygen-sensitive products first and filling-speed problems second, so the filler is specified around dissolved oxygen and closure integrity.
Key facts at a glance
Valve typeIsobaric for beer, gravity or volumetric for wine and spirits
Output range4,000-20,000 BPH on glass
BottleGlass, 200-750 ml typical, crown or ROPP closure
Key controlDissolved oxygen, fill height, closure torque
Line scopeRinser, filler, capper or crowner, labeller, packer
CleaningCIP with caustic and rinse cycles

Why does beer need counter-pressure filling?

Beer carries dissolved CO2 and is extremely sensitive to oxygen. Counter-pressure filling keeps CO2 in solution and limits contact with air. The alternative, filling warm and flat, destroys the head and shortens shelf life. This is why a beer filler and a wine filler are rarely the same machine.

What does dissolved oxygen do to beer and wine?

Oxygen drives staling. In beer it shows as cardboard and paper notes within weeks; in wine it flattens fruit and browns the colour. The main entry points are the filler bowl, the space between fill and closure, and the closure itself. Measuring in the finished bottle is the only number that counts.

PackageFillingLine rate on glass
Glass bottle, crownIsobaric4,000-20,000 BPH
Glass bottle, ROPPIsobaric or gravity4,000-20,000 BPH
Aluminum canIsobaric + seamerUp to 25,000 CPH
PET, short shelf lifeIsobaricHigher rate, lower barrier

For the same duty in another bottle format, the Filling Machine for Glass CSD is specified separately.

Why do glass lines run slower than PET lines?

Glass weighs more, breaks, and needs mechanical spacing instead of an air conveyor. Every transfer is a potential breakage point, so the line runs at a lower rate and with more accumulation. A 20,000 BPH glass line is a different engineering problem from a 20,000 BPH PET line.

Throughput and change-part lists are on the Gravity Filling Machine for Glass Bottle Wine page rather than in this note.

What does a beer line need for foam control?

A cold fill, a controlled pressure release and a clean glass. Beer foams on the way into the bottle if the pressure drops too fast, and a foaming fill gives a short volume and a wet crown. The pressure ramp is the setting that matters.

The same question is worked through from another angle in How Gravity Filling Machines Handle Wine in Glass Bottles.

How to read the numbers. Rated capacity in this note follows the product specification range, not a factory acceptance test. CIP, filling-temperature pull-down and package changeover sit outside a rated BPH, so plan on 0.60-0.80.

Frequently asked questions

Why does the fill height vary on a glass line?

Glass bottle capacity varies from mould to mould, so filling to a level gives a varying volume. Filling to a volume, or check-weighing after fill, is how glass lines hold a consistent net content.

What is the difference between a beer filler and a CSD filler?

Both are isobaric. A beer filler is built around oxygen pick-up and foam control at the crowner; a CSD filler is built around CO2 retention and higher speed. The valve principle is shared, the details are not.

How is a glass line protected against breakage?

By mechanical spacing instead of an air conveyor, guarded transfers, and a breakage detection point that stops the line before the fragments travel. Glass lines carry more inspection than PET lines for this reason.

Can a wine line run without a corker?

It needs a closure station matched to the closure: cork, screw cap or crown. The filler and the closure machine are specified together, because the bottle finish and the head are one decision.

Key takeaways
  1. Beer is a dissolved-oxygen problem before it is a filling-speed problem.
  2. Glass runs slower than PET because of weight, breakage and spacing.
  3. Each closure type needs its own capping head, not an adjustment.
  4. CIP time is not production time and must not be planned as if it were.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.