Case Study: Successful Aluminum Can Juice Line Installation

Views: 1617 Author: Howie SUN Publish Time: Update Time:
Aluminum cans fill faster than bottles and forgive less: dissolved oxygen and seam tightness decide shelf life, and neither is visible on the line.
Key facts at a glance
Filling systemIsobaric for beer and CSD, volumetric for juice and tea
Rated outputUp to 25,000 CPH
Can rangeStandard 250, 330 and 500 ml
SeamingRoller seamer integrated with the filler
OptionsHot fill for juice and tea, nitrogen dosing
Key controlFill level, seam tightness, dissolved oxygen

Why is can filling measured in CPH and not BPH?

A can line is counted in cans per hour because the container is the unit the seamer closes. CPH and BPH cannot be converted without the fill volume, and the downstream packer is sized in cases per hour. Comparing a 24,000 CPH can line with a 24,000 BPH bottle line compares two different plants.

What changes between a beer can and a juice can?

Beer and CSD run isobaric, cold, under counter-pressure. Juice and tea often run hot fill or a volumetric fill with a downstream pasteuriser. The can is the same format; the filler, the valve set and the temperature control are not, so one can line rarely covers both without a second specification.

ProductFilling principleCritical measurement
BeerIsobaric, coldDissolved oxygen and seam tightness
CSD and sodaIsobaric, coldCO2 retention and fill height
Juice and teaVolumetric or hot fillFill temperature and seam integrity
Energy drinksIsobaric or volumetricDissolved oxygen and closure

The Aluminum Can Filling Machine for Hotfill Juice and Tea is the matching unit when this becomes a line project.

What does a can line cost to run that buyers forget?

Compressed air for the seamer and the air conveyor, CO2 for purging, and the tear-down cans used for seam checks every shift. None of these appear in the machine price. A line running 24,000 CPH can consume a measurable share of its operating cost in air alone.

Site requirements, air and water consumption sit with the Volumetric Aluminum Can Filling Machine for Hotfill Juice.

How does the filler synchronise with the seamer?

The filler discharges cans onto a transfer star wheel that hands each can to the seamer at a fixed pitch. Any slip at that transfer shows up as a damaged flange and a failed seam. The transfer is the most alignment-sensitive point on a can line.

The same question is worked through from another angle in How Aluminum Can Filling Machines Handle Hotfill Beverages.

How to read the numbers. Treat the capacity figures as reference ranges from the product specification. A rated CPH is a steady-state figure at one can size; seamer adjustment and CIP sit outside it, so size on 0.65-0.85.

Frequently asked questions

Why do cans dent on the conveyor?

Usually conveyor pressure or a jam at a transfer, not the can quality. Air conveyor pressure, guide rail gaps and accumulation length are the three settings to check first.

Can a can line run 330 ml and 500 ml in one shift?

With change parts for the filler, the seamer and the conveyor, yes. The changeover is longer than a label change and is normally scheduled between campaigns.

Why does a seam fail the tear-down?

Usually seamer roll pressure, chuck wear or a can flange outside tolerance. The tear-down measures the result; the cause is found by checking the rolls and the can supplier specification together.

Does a 250 ml can run faster than a 500 ml can?

Yes, at the same filler, because the fill volume per cycle is smaller. The seamer and the packer still have to carry the higher can rate, which is why the line rating is set on cans per hour, not litres.

Key takeaways
  1. CPH and BPH are different units; never compare them directly.
  2. Dissolved oxygen in the finished can is the number that decides shelf life.
  3. The seamer transfer is the most alignment-sensitive point on a can line.
  4. A failed seam is a roll and flange problem, found by measurement.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.