Bottled Water vs CSD vs Juice: Which Segment Drives Your Filling Machine Investment?

Views: 263 Author: Howie SUN Publish Time: Update Time:
A CSD line is judged by the CO2 left in the sealed bottle, not by the volumes set at the mixer, and the gap between the two is where most projects lose money. Higher margin but needs isobaric CSD filling and can/PET rated for pressure.

12,000 BPH (60ml) Filling Machine

Key facts at a glance
Filling principleIsobaric, CO2 counter-pressure
Rated output12,000-36,000 BPH at 0.2-2 L
ContainersPET bottle, glass bottle, aluminum can
CO2 handlingPre-pressurisation and return pipe, no venting
ValvesMechanical, semi-electric or volumetric
Line scopeWater treatment, syrup mixing, carbonation, filler, pack

Mechanical, semi-electric or volumetric valves: what is the difference?

Mechanical valves open and close on a fixed cam profile and are the most forgiving on maintenance. Semi-electric valves use a signal to open and close, so the fill window can be set per recipe. Volumetric valves dose a chamber and hold accuracy when bottle pressure or product temperature drifts during the shift.

Higher margin but needs isobaric CSD filling and can/PET rated for pressure.

Where does foam actually come from?

Foam is usually a temperature or pressure problem, not a valve problem. Warm product, a fast pressure release at the end of fill, a worn seal that lets gas bypass, or a dirty return pipe all show up as foam at the same place. Check the product temperature and the pressure ramp before touching the valves.

Valve typeSettingBest for
MechanicalFixed cam profileSingle product, long runs
Semi-electricSignal-timed open and closeRecipe changes within one product family
VolumetricChamber dosePressure or temperature drift during the shift
Isobaric + volumetricChamber dose under counter-pressureHigh CO2 with tight fill accuracy

Valve count, utility schedule and footprint sit on the Isobaric Filling Machine for CSD and Sparkling Water page.

How does a can line differ from a PET line for CSD?

A can is filled and seamed, a PET bottle is filled and capped. Cans run faster per unit and are counted in CPH; PET allows larger formats and a lighter package. The filler principle is the same isobaric one, the closing equipment and the line rate are not.

Throughput and change-part lists are on the CSD & Sparkling Water by Mechanical Filler page rather than in this note.

What is overfoaming at the filler and how is it controlled?

Overfoaming is gas leaving the product too fast at the end of fill. The pressure release has to be ramped, not dumped, and the fill height has to leave the right headspace. A snift valve that opens too early turns a good fill into a wet bottle.

The same question is worked through from another angle in How Nitrogen Dosers Extend Shelf Life of Carbonated Drinks.

How to read the numbers. The capacity tab on the specification sheet gives ranges; treat them as such. Changeover, CIP and downstream stops are outside the rating. Plan on 0.65-0.85, and check CO2 supply on average rather than peak draw.

Frequently asked questions

Can one filling machine run both still water and CSD?

No. Carbonation needs isobaric valves under counter-pressure; still water runs gravity or volumetric. A combiblock can carry both valve sets, but they are specified separately and are not interchangeable at the push of a button.

Why is my fill level dropping through the shift?

Usually product temperature rising in the bowl or a worn valve seal. Both change the pressure balance, so the fill cuts off earlier. Log bowl temperature and fill weight together for one shift before changing any valve.

How many cans per hour is 24,000 CPH?

400 cans per minute. CPH and BPH are different units and cannot be compared directly, because can and bottle formats carry different volumes and different downstream equipment.

What causes a foaming spike at start-up?

Warm product and an empty bowl. The first bottles see the largest pressure step. A short recirculation before production and a controlled bowl cool-down remove most of it.

Key takeaways
  1. Carbonation is a pressure and temperature problem before it is a valve problem.
  2. Judge a CSD line on CO2 retention in the filled bottle, not on the mixer set point.
  3. Warm product loses CO2 before the filler can dose it.
  4. A can line and a PET line share the valve principle, not the closing equipment.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.