Advantages of Gravity Filling Machines for Still Water

Views: 2048 Author: Howie SUN Publish Time: Update Time:
A bottle water line is treatment, blowing, filling, capping and packing in one chain, and its real output is set by the slowest station in that chain rather than by the filler nameplate.
Key facts at a glance
ApplicationStill water, RO water, mineral water
Filling methodGravity or volumetric valve
Rated output5,000-48,000 BPH at 500 ml
Container range200 ml to 16 L, by configuration
Contact materialSUS 304 product contact, CIP-ready
Line scopeTreatment, blowing, filling, capping, labelling, packing

What does a water line have to get right before speed matters?

Raw water, neck finish and the filler-capper match decide more about a water line than its BPH. BPH takes the meeting; the neck finish and the capper match get the last five minutes. Rinser clamps and capping heads are cut for one neck finish; a 1 mm thread change means new change parts rather than a new machine.

Gravity, volumetric or isobaric: which filling system fits?

Gravity filling holds a level in a rigid bottle and costs least per valve. Volumetric filling doses a fixed volume into a chamber, so it holds accuracy across 3 L, 5 L and 10 L formats without changing the head. Isobaric filling is for carbonated product only, because it keeps CO2 in solution under counter-pressure. A still water line never needs it.

Filling principleBest forWatch out for
GravityStill water, one rigid bottle sizeThin-wall bottles deform under head pressure
Volumetric valve3-15 L and mixed formatsValve wear shows as slow drift, not a sudden error
IsobaricCarbonated water onlyNeeds counter-pressure, so slower per valve
Load cellOil and high-value liquidSlower cycle, higher cost per valve

For the same duty in another bottle format, the Blow-fill-cap Combibloc for Still Water is specified separately.

What does a small 2,000-6,000 BPH line give up?

A small line gives up automation, not quality. Manual or semi-automatic packing, fewer accumulation buffers, and a simpler CIP usually follow. What it should not give up is the filling valve and the capping head, because those two decide whether the product is saleable.

The Gravity Filling Machine for Still Water is the reference unit for this configuration.

Does bottle lightweighting change the filler?

A lighter bottle is less rigid, so it deforms more under the filling head and grips differently in the star wheels. The filler may need a different neck handling and a lower contact pressure. Lightweighting is a bottle project that reaches into the filling line.

The same question is worked through from another angle in How to Choose Between Gravity, Pressure, and Volumetric Filling.

How to read the numbers. Where a BPH appears below it is the specification range, not a measured rate. Changeover between bottle formats, CIP and downstream stops sit outside a rated BPH, so plan on 0.65-0.85.

Frequently asked questions

How many bottles per minute is 12,000 BPH?

200 bottles per minute. Divide BPH by 60. A 24,000 BPH line runs at 400 bottles per minute, which is why filler and packer have to be matched rather than bought separately.

Can one water line run 500 ml and 1.5 L bottles?

Yes, with change parts: star wheels, guide rails, grippers and a filling recipe. Budget 40-90 minutes per switch and expect the production factor to drop from about 0.85 to 0.70.

What utilities does a 12,000 BPH water line need?

Plan for 380 V three-phase power, 0.6-0.8 MPa compressed air, and a chiller if blow molding runs in-house. Exact consumption belongs in the utility schedule of the quotation, not in a rule of thumb.

Can a still water line be converted to carbonated later?

Not on the same filler. Carbonation needs isobaric valves, a CO2 dosing and mixing unit, and a different bowl. A combiblock can carry both valve sets, but they are separate specifications, not a field conversion.

Key takeaways
  1. Capacity is the rating of the slowest station, not the filler nameplate.
  2. Size with a production factor of 0.65-0.85, never 1.0.
  3. Change parts and filling system are settled by neck finish and bottle rigidity, well before BPH.
  4. A 5 L line and a 500 ml line are separate specifications; treating them as one flexible option is where budgets slip.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.