What Is NFC Juice? Is It Really Healthier?

Views: 18253 Author: Howie SUN Publish Time: Update Time:
Juice is a product-first decision: acidity, pulp and heat sensitivity choose the filling temperature, and the temperature chooses the bottle. According to Chinese standards, it is sufficient for the original juice content in this type of beverage to exceed 10%.

1

Key facts at a glance
Filling systemHot-fill, up to 85 C
Capacity6,000-36,000 BPH at 0.2-2 L
PackageHeat-resistant PET geometry, or glass
LineHot-fill monobloc with tunnel pasteuriser
ProductsJuice, tea, nectar, functional drinks
Key controlFill temperature, hold time, cap seal

Why does juice get filled hot instead of cold?

Hot filling does two jobs at once: it pasteurises the product on the way to the filler, and the residual heat sanitises the bottle and cap. That is why a hot-fill line can run an acidic juice without a separate bottle steriliser. The price is a heat-resistant bottle and a longer cooling tunnel.

As people increasingly tend to pursue natural and fresh food, juice processing technology continues to innovate, developing non concentrated and reduced juice that does not require high-temperature concentration.

What does the fill temperature actually control?

Fill temperature and hold time together set the pasteurisation result. Below the target, shelf life is at risk; above it, the product cooks and the bottle deforms. The number belongs to the product and the bottle, not to the machine, and it should be written into the acceptance protocol with a tolerance.

RouteTemperatureWhat it costs
Hot fillUp to 85 CHeat-resistant bottle and a cooling tunnel
Cold fill with preservativeAmbientFormulation constraint, not a machine constraint
Cold fill with in-line pasteuriserProduct-side onlySeparate pasteuriser and a closed filling zone
Hot fill in glassUp to 85 CGlass mass, slower line, higher transport cost

Where this becomes a line rather than a single machine, the Juice By Volumetric Filler is the starting point.

How do you compare a hot-fill line with a cold-fill line?

Compare them on the product, not on the machine. Hot fill suits acidic juice and tea in heat-resistant PET. Cold fill needs a preservative system or a separate sanitising step, but it protects heat-sensitive flavours and vitamins and uses a lighter bottle. The decision is a product decision with a packaging cost attached.

But compared to juice drinks and 100% reduced juice, NFC juice has more nutritional components.

The specification sheet for the Hotfill Type Filling Machine for Juice carries the utility figures quoted here.

When is cold filling the better route?

Cold filling protects heat-sensitive flavour and colour and allows a lighter bottle. It needs either a preservative system or a validated cold chain, and it moves the microbial control to the product and the plant rather than to the filler. The decision is commercial before it is technical.

The same question is worked through from another angle in How to Improve Juice Filling Accuracy with Load Cells.

What does a tea line need that a juice line does not?

Tea usually needs finer filtration, deaeration to protect aroma, and a fill temperature that does not strip the volatile notes. Tea also clouds after cooling, so the clarification step is part of the product design, not a filling detail.

How to read the numbers. The numbers in the tables are reference ranges taken from the product specification. A rated BPH covers filling only. Pasteurisation, hold time and cooling sit outside it, so size on 0.65-0.85.

Frequently asked questions

What temperature is juice hot-filled at?

Up to 85 C, set per product and per bottle. The exact set point and tolerance belong in the product specification, because acidity, pulp content and bottle wall thickness all move it.

How long does a hot-fill line take to reach temperature?

It depends on the hold tube volume and the heater capacity. The line is not production-ready until the return temperature is stable, so start-up time belongs in the daily plan rather than being discovered at shift start.

Why does juice lose colour after hot filling?

Heat-sensitive pigments and vitamins degrade above the product temperature limit. The fill temperature and the hold time are the two variables; lowering either protects colour and shortens the microbial margin.

Can a hot-fill line run clear juice and pulp juice?

With a filter change and a different valve bore for the pulp, yes. Clear juice needs finer filtration, and pulp needs agitation in the bowl so the fibre does not settle.

What cooling profile does a hot-fill bottle need?

A controlled ramp rather than a cold plunge, so the bottle does not deform under vacuum. The tunnel zones are set per bottle geometry and validated with a temperature probe in the product.

Key takeaways
  1. Hot fill does pasteurisation and bottle sanitising in one step, and charges for it in bottle cost.
  2. Pulp needs bore and agitation, not more pressure.
  3. Cap seals and valve O-rings are the first wear items on a hot line.
  4. Colour loss is a temperature and hold-time decision.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.