How Volumetric Fillers Improve Consistency in Carbonated Soft Drinks

Views: 1765 Author: Howie SUN Publish Time: Update Time:
Carbonated filling is a pressure and temperature problem: CO2 stays in the product only while the bottle is held above the saturation pressure for its temperature.
Key facts at a glance
Filling principleIsobaric, CO2 counter-pressure
Output range12,000-36,000 BPH at 0.2-2 L
ContainersPET bottle, glass bottle, aluminum can
CO2 handlingPre-pressurisation and return pipe, no venting
ValvesMechanical, semi-electric or volumetric
Line scopeWater treatment, syrup mixing, carbonation, filler, pack

Why does carbonated product need isobaric filling?

A carbonated drink is a saturated solution held in equilibrium by pressure and temperature. If the filler exposes it to atmosphere, CO2 leaves the liquid as foam and the fill level collapses. Isobaric filling pressurises the bottle to the bowl pressure first, fills under counter-pressure, then releases in a controlled ramp.

What decides CO2 retention on the line?

Four points decide it: the carbonation level set at the mixer, the product temperature at the filler, the pressure profile during fill, and the time between capping and packing. A line that holds 4.0 volumes at the mixer can deliver 3.4 in the bottle if the filler bowl runs warm or the capping head leaks.

Valve typeSettingBest for
MechanicalFixed cam profileSingle product, long runs
Semi-electricSignal-timed open and closeRecipe changes within one product family
VolumetricChamber dosePressure or temperature drift during the shift
Isobaric + volumetricChamber dose under counter-pressureHigh CO2 with tight fill accuracy

Sizing for this duty runs through the CSD & Sparkling Water by Mechanical Filler, where the valve count is set out.

Mechanical, semi-electric or volumetric valves: what is the difference?

Mechanical valves open and close on a fixed cam profile and are the most forgiving on maintenance. Semi-electric valves use a signal to open and close, so the fill window can be set per recipe. Volumetric valves dose a chamber and hold accuracy when bottle pressure or product temperature drifts during the shift.

Rated output, change parts and services are listed on the Isobaric Filling Machine for CSD and Sparkling Water page.

What does warm product do to a CSD line?

Warm product holds less CO2 at the same pressure, so the filler either loses gas or needs a higher pressure that increases foaming. Chilling before carbonation is the standard answer, and the chiller capacity belongs in the utility schedule.

The same question is worked through from another angle in Order for sparkling water bottling line from Turks and.

How to read the numbers. The capacity tab on the specification sheet gives ranges; treat them as such. Changeover, CIP and downstream stops are outside the rating. Plan on 0.65-0.85, and check CO2 supply on average rather than peak draw.

Frequently asked questions

What CO2 level can an isobaric filler hold?

It holds what the mixer sets and the temperature allows. Most CSD runs between 2.5 and 4.0 volumes, with the target set per product. Retention, not the mixer set point, is what the acceptance test should measure in the filled bottle.

Why is my fill level dropping through the shift?

Usually product temperature rising in the bowl or a worn valve seal. Both change the pressure balance, so the fill cuts off earlier. Log bowl temperature and fill weight together for one shift before changing any valve.

How many cans per hour is 24,000 CPH?

400 cans per minute. CPH and BPH are different units and cannot be compared directly, because can and bottle formats carry different volumes and different downstream equipment.

Can a CSD line fill glass bottles?

Yes, with a different infeed, spacing and capping set. Glass needs mechanical spacing rather than an air conveyor, and the filler runs at 4,000-20,000 BPH on glass against 12,000-36,000 BPH on PET.

Key takeaways
  1. Carbonation is a pressure and temperature problem before it is a valve problem.
  2. Semi-electric and volumetric valves buy recipe flexibility; mechanical valves buy simplicity.
  3. Size the CO2 plant on average demand, not on the filler nameplate.
  4. A can line and a PET line share the valve principle, not the closing equipment.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.