How Combibloc Fillers Streamline Edible Oil Production

Views: 1639 Author: Howie SUN Publish Time: Update Time:
Oil filling fails on drip and density, not on speed. A load cell fixes the density problem; the valve cut-off fixes the drip.
Key facts at a glance
Filling systemLoad cell net-weight, or piston dosing
Capacity range12,000-36,000 BPH at 0.2-2 L
ViscosityUp to 10,000 cP
AccuracyPlus or minus 0.5 g per bottle
Bottle or canPET or glass
Key controlWeight per bottle, temperature, drip-free cut-off

What does the filling valve have to do about dripping?

Oil clings. A valve that cuts off cleanly on water leaves a thread of oil on the bottle shoulder, and that thread becomes a rejected bottle and a dirty conveyor. The cut-off profile, the nozzle tip and the suck-back setting are the three things to watch at acceptance, not the fill speed.

How does viscosity change the line design?

Above a few thousand cP the product moves by pressure and time rather than by gravity, so the bowl, the feed pipe and the valve bore all grow. Temperature control also becomes part of the filling specification, because a cold oil at 10 C and the same oil at 25 C behave like two different products.

Dosing methodAccuracy basisWhen it fits
Load cellNet weight per bottleDensity moves with temperature
PistonDisplacement volumeStable density, high speed, thick product
Volumetric valveChamber volumeLow-viscosity oil at steady temperature
Flow meterMeasured volumeContinuous flow, limited pulp or solids

For the same duty in another bottle format, the Edible Oil Load Cell is specified separately.

What is the acceptance test for an oil filler?

Weigh a fixed sample at the start, middle and end of a shift, on the same scale, and record the temperature at the same time. A filler that holds plus or minus 0.5 g at a steady 25 C may drift at 18 C. Acceptance without a temperature record is an argument waiting to happen.

Throughput and change-part lists are on the Filling Machine for Viscous Product page rather than in this note.

How is an oil filler cleaned between products?

With a warm flush and a full drain, because oil does not rinse like water. The circuit needs a low point for drainage and a filter on the return. A change between two oils is quicker than a change from oil to a water-based product.

The same question is worked through from another angle in Benefits of Using Load Cell Combiblocs for Edible Oil.

What does bottle weight variation do to a load cell filler?

Nothing, if the filler tares each bottle before dosing. That tare step is what separates net-weight filling from a flow meter. Without it, a heavy bottle delivers less product and the label claim fails.

How to read the numbers. The capacity figures here are reference ranges taken from the product specification. Changeover, CIP and temperature drift sit outside a rated BPH. Plan on 0.65-0.85 and check the pump curve at the lowest product temperature.

Frequently asked questions

Why does oil foam or bubble during filling?

Usually air entrained in the product or a fill that starts too fast. Letting the product settle in the bowl and ramping the valve opening removes most of it without changing the pump.

Does edible oil need nitrogen?

Some packers dose nitrogen into the headspace to slow oxidation, especially for polyunsaturated oils. It is an option, and its value depends on the oil and the target shelf life, not on the filler.

What temperature should oil be filled at?

The temperature at which the viscosity gives a clean cut-off and a repeatable weight, held steady through the shift. The exact band belongs to the product specification; the requirement is that it is controlled and recorded.

What causes weight drift on an oil filler?

Product temperature, a worn valve seat, or scale calibration. Log the weight and the temperature together; a drift that follows temperature is a process problem, not a valve problem.

Does edible oil need hot filling?

No. Oil is filled at the temperature that gives a clean cut-off and a stable weight. Heating is used to lower viscosity when the product is cold, not to preserve it.

Key takeaways
  1. A clean cut-off matters as much as accuracy, because drips become rejects.
  2. Acceptance needs a weight and a temperature recorded together.
  3. Weight, not volume, is the legal fill for oil.
  4. A temperature record turns an accuracy argument into a measurement.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.