How Aluminum Can Fillers Handle Hot and Cold Beverages

Views: 1754 Author: Howie SUN Publish Time: Update Time:
A can line is rated in cans per hour because the seamer sets the pace, and the seam, not the filler, is where the rating is usually lost. Maintaining optimal pressure throughout the filling process is critical to prevent overfilling or underfilling of cans, which could lead to product wastage or quality issues.
Key facts at a glance
Filling methodIsobaric for beer and CSD, volumetric for juice and tea
CapacityUp to 25,000 CPH
Can sizesStandard 250, 330 and 500 ml
SeamingRoller seamer integrated with the filler
OptionsHot fill for juice and tea, nitrogen dosing
Key controlFill level, seam tightness, dissolved oxygen

How is oxygen controlled on a can line?

Dissolved oxygen enters at three points: deaeration of the product, the filler bowl atmosphere, and the gap between fill and seam. Nitrogen dosing and a steam or CO2 tunnel at the seamer reduce the last one. For beer and juice, the dissolved oxygen in the finished can is the number to test, not the setting on the doser.

Maintaining optimal pressure throughout the filling process is critical to prevent overfilling or underfilling of cans, which could lead to product wastage or quality issues.

What changes between a beer can and a juice can?

Beer and CSD run isobaric, cold, under counter-pressure. Juice and tea often run hot fill or a volumetric fill with a downstream pasteuriser. The can is the same format; the filler, the valve set and the temperature control are not, so one can line rarely covers both without a second specification.

Aluminum can fillers equipped with advanced temperature control mechanisms can efficiently fill both hot and cold beverages.

ProductFilling principleCritical measurement
BeerIsobaric, coldDissolved oxygen and seam tightness
CSD and sodaIsobaric, coldCO2 retention and fill height
Juice and teaVolumetric or hot fillFill temperature and seam integrity
Energy drinksIsobaric or volumetricDissolved oxygen and closure

Where this becomes a line rather than a single machine, the Aluminum Can Filling Machine for Beer, Carbonated Soft Drink is the starting point.

How does the filler synchronise with the seamer?

The filler discharges cans onto a transfer star wheel that hands each can to the seamer at a fixed pitch. Any slip at that transfer shows up as a damaged flange and a failed seam. The transfer is the most alignment-sensitive point on a can line.

A different bottle format means a different unit; see the Aluminum Can Filling Machine for Hotfill Juice and Tea.

What is the smallest viable can line?

Small can lines exist for craft producers, usually with a compact filler-seamer and manual or semi-automatic packing. The limit is not the filler but the seam quality control, which needs a tear-down station and a trained operator at any volume.

The same question is worked through from another angle in How to Select the Right Aluminum Can Filler for.

How to read the numbers. The output figures are specification ranges; the measured rate depends on the product and the shift. Seamer stops, can-size changeover and downstream accumulation sit outside a rated CPH, so plan on 0.65-0.85.

Frequently asked questions

How many cans per minute is 18,000 CPH?

300 cans per minute. Divide CPH by 60. The seamer, the filler and the packer all have to carry that number, so the line rating is the lowest of the three.

What is dissolved oxygen and why does it matter?

It is the oxygen left in the product after filling. It drives oxidation, off-flavour and haze. Beer and juice have tight limits, and the measurement belongs in the acceptance protocol, taken from the finished can.

Why do cans dent on the conveyor?

Usually conveyor pressure or a jam at a transfer, not the can quality. Air conveyor pressure, guide rail gaps and accumulation length are the three settings to check first.

Can a can line run 330 ml and 500 ml in one shift?

With change parts for the filler, the seamer and the conveyor, yes. The changeover is longer than a label change and is normally scheduled between campaigns.

Key takeaways
  1. CPH and BPH are different units; never compare them directly.
  2. The seamer, not the filler, is where a can line loses its rating.
  3. Beer and juice cans share a format, not a filling specification.
  4. A failed seam is a roll and flange problem, found by measurement.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.