Advantages of Volumetric Juice Fillers Over Mechanical Fillers

Views: 1523 Author: Howie SUN Publish Time: Update Time:
Hot filling pasteurises the product and sanitises the bottle in one pass, which is why acidic juice and tea can be filled without a separate bottle steriliser.
Key facts at a glance
Filling systemHot-fill, up to 85 C
Output range6,000-36,000 BPH at 0.2-2 L
BottleHeat-resistant PET geometry, or glass
LineHot-fill monobloc with tunnel pasteuriser
ProductsJuice, tea, nectar, functional drinks
Key controlFill temperature, hold time, cap seal

How do you keep pulp and fibre moving through the line?

Pulp needs either a larger valve bore or a piston filler, and it needs continuous gentle agitation in the bowl. Dead corners in the product path settle fibre, then release it as a slug into the next bottle. Bowl geometry and return-flow design matter more than valve count here.

What breaks first on a hot-fill line?

Cap seals and filling valve O-rings, because they see the highest temperature every cycle. A seal that is fine on a water line at 20 C will harden in weeks at 85 C. The spare parts list should carry those two items in proportion to the number of valves, not as a single set.

RouteTemperatureWhat it costs
Hot fillUp to 85 CHeat-resistant bottle and a cooling tunnel
Cold fill with preservativeAmbientFormulation constraint, not a machine constraint
Cold fill with in-line pasteuriserProduct-side onlySeparate pasteuriser and a closed filling zone
Hot fill in glassUp to 85 CGlass mass, slower line, higher transport cost

The Juice By Volumetric Filler is the reference unit for this configuration.

What does a tea line need that a juice line does not?

Tea usually needs finer filtration, deaeration to protect aroma, and a fill temperature that does not strip the volatile notes. Tea also clouds after cooling, so the clarification step is part of the product design, not a filling detail.

The unit behind this configuration is the Hotfill Type Filling Machine for Juice.

What does a glass juice line change?

Glass brings mass, breakage and a slower line. It also brings a closure decision: crown, lug or screw. A glass hot-fill line usually runs at a lower rate than the same filler on PET, and the difference is handling and inspection, not the valve.

The same question is worked through from another angle in Volumetric Filling Machines for Still Water and Juices.

How to read the numbers. All capacity numbers here are the ranges published in the product specification. Pasteuriser heat-up, hold and cooling sit outside a rated BPH, so plan on 0.65-0.85.

Frequently asked questions

What temperature is juice hot-filled at?

Up to 85 C, set per product and per bottle. The exact set point and tolerance belong in the product specification, because acidity, pulp content and bottle wall thickness all move it.

Why does the bottle panel after filling?

Usually fill temperature above the bottle rating, or a vacuum that forms as the product cools. Check the fill temperature against the bottle specification and the cap seal before changing the cooling profile.

Can one line run juice and tea?

Yes, if the filler, the recipe and the downstream cooling are specified for both. Tea usually needs a finer filtration step and a different deaeration setting, so the changeover is a recipe and filter change, not just a new label.

Can a hot-fill line run clear juice and pulp juice?

With a filter change and a different valve bore for the pulp, yes. Clear juice needs finer filtration, and pulp needs agitation in the bowl so the fibre does not settle.

Key takeaways
  1. Hot fill does pasteurisation and bottle sanitising in one step, and charges for it in bottle cost.
  2. Fill temperature is a product and package number, not a machine setting.
  3. A change of fill temperature invalidates the shelf-life trial.
  4. Cool the bottle on a ramp, not a plunge.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.