A Guide to Common Materials Used in Water Filling Machine Construction

Views: 2773 Author: Howie SUN Publish Time: Update Time:
Bottled water is the simplest beverage to fill and the easiest line to oversize, because the filler rating hides the treatment ceiling, the changeover time and the packer limit. Common seal materials include silicone, EPDM, and Viton, each offering varying levels of durability, chemical resistance, and temperature tolerance.
Key facts at a glance
ApplicationStill water, RO water, mineral water
Valve typeGravity or volumetric valve
Rated output5,000-48,000 BPH at 500 ml
Bottle sizes200 ml to 16 L, by configuration
Wetted partsSUS 304 product contact, CIP-ready
Line scopeTreatment, blowing, filling, capping, labelling, packing

What does a water line have to get right before speed matters?

A water line stands or falls on three inputs: raw water analysis, neck finish, and how well filler and capper are matched. Most of the meeting goes on BPH; the other two get a fraction of the time. Change the thread by a millimetre and the rinser clamp and capping head have to change with it.

Stainless steel components, especially those made from 316 grade, offer superior longevity and resistance to corrosion, reducing the need for frequent repairs and replacements.

Gravity, volumetric or isobaric: which filling system fits?

Gravity filling holds a level in a rigid bottle and costs least per valve. Volumetric filling doses a fixed volume into a chamber, so it holds accuracy across 3 L, 5 L and 10 L formats without changing the head. Isobaric filling is for carbonated product only, because it keeps CO2 in solution under counter-pressure. A still water line never needs it.

Filling principleBest forWatch out for
GravityStill water, one rigid bottle sizeThin-wall bottles deform under head pressure
Volumetric valve3-15 L and mixed formatsValve wear shows as slow drift, not a sudden error
IsobaricCarbonated water onlyNeeds counter-pressure, so slower per valve
Load cellOil and high-value liquidSlower cycle, higher cost per valve

The unit behind this configuration is the Blow-fill-cap Combibloc for Still Water.

How is a water line cleaned, and how often?

A water line is cleaned on a fixed cycle plus a changeover clean. The circuit covers the filler bowl, the product pipes and the filling valves. Ozone or heat is used for disinfection, and the cycle time is a planned stop rather than an incident.

Sizing for this duty runs through the Gravity Filling Machine for Still Water, where the valve count is set out.

Does bottle lightweighting change the filler?

A lighter bottle is less rigid, so it deforms more under the filling head and grips differently in the star wheels. The filler may need a different neck handling and a lower contact pressure. Lightweighting is a bottle project that reaches into the filling line.

Common seal materials include silicone, EPDM, and Viton, each offering varying levels of durability, chemical resistance, and temperature tolerance.

The same question is worked through from another angle in Tips for Reducing Downtime in Volumetric Water Filling Lines.

How to read the numbers. All capacity numbers here are the ranges published in the product specification. Changeover between bottle formats, CIP and downstream stops sit outside a rated BPH, so plan on 0.65-0.85.

Frequently asked questions

How many bottles per minute is 12,000 BPH?

200 bottles per minute. Divide BPH by 60. A 24,000 BPH line runs at 400 bottles per minute, which is why filler and packer have to be matched rather than bought separately.

What water treatment does a bottled water line need?

It follows the raw water analysis, not a standard package. Surface water usually needs multi-media filtration, RO and UV or ozone. Low-hardness municipal water may need only carbon filtration and disinfection.

Can a still water line be converted to carbonated later?

Not on the same filler. Carbonation needs isobaric valves, a CO2 dosing and mixing unit, and a different bowl. A combiblock can carry both valve sets, but they are separate specifications, not a field conversion.

What is the acceptable fill level tolerance for water?

Commercial practice is a stated band per bottle size, typically checked by weight at the filler outlet. The band belongs in the acceptance protocol. A line without a written tolerance will argue about it at commissioning.

Key takeaways
  1. Size with a production factor of 0.65-0.85, never 1.0.
  2. Capacity planning starts with CIP and changeover, not with the filler nameplate.
  3. It is the bottle format, not the BPH target, that picks the filling system.
  4. Five-litre and 500 ml formats are two specifications, not two settings on one machine.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.