Volumetric Can Filling for Precise Hot Fill Juice Applications

Views: 1843 Author: Howie SUN Publish Time: Update Time:
Aluminum cans fill faster than bottles and forgive less: dissolved oxygen and seam tightness decide shelf life, and neither is visible on the line.
Key facts at a glance
Filling methodIsobaric for beer and CSD, volumetric for juice and tea
CapacityUp to 25,000 CPH
Can formatStandard 250, 330 and 500 ml
SeamingRoller seamer integrated with the filler
OptionsHot fill for juice and tea, nitrogen dosing
Key controlFill level, seam tightness, dissolved oxygen

What does the seamer have to get right?

A can is sealed by two rolling operations that fold the can flange and the end together. Seam thickness, seam height and overlap are checked by tear-down at a fixed interval, not by eye. A seam that looks right and measures wrong leaks three weeks later, in the customer warehouse rather than on your line.

What changes between a beer can and a juice can?

Beer and CSD run isobaric, cold, under counter-pressure. Juice and tea often run hot fill or a volumetric fill with a downstream pasteuriser. The can is the same format; the filler, the valve set and the temperature control are not, so one can line rarely covers both without a second specification.

ProductFilling principleCritical measurement
BeerIsobaric, coldDissolved oxygen and seam tightness
CSD and sodaIsobaric, coldCO2 retention and fill height
Juice and teaVolumetric or hot fillFill temperature and seam integrity
Energy drinksIsobaric or volumetricDissolved oxygen and closure

The specification sheet for the Aluminum Can Filling Machine for Hotfill Juice and Tea carries the utility figures quoted here.

What does a can line cost to run that buyers forget?

Compressed air for the seamer and the air conveyor, CO2 for purging, and the tear-down cans used for seam checks every shift. None of these appear in the machine price. A line running 24,000 CPH can consume a measurable share of its operating cost in air alone.

A different bottle format means a different unit; see the Volumetric Aluminum Can Filling Machine for Hotfill Juice.

What does a hot-fill can line need that a cold line does not?

A heated product path, a fill temperature control loop and a cooling tunnel after seaming. The can itself tolerates the heat; the lining and the product do not always. The temperature window belongs to the product specification.

The same question is worked through from another angle in How Volumetric Aluminum Can Fillers Ensure Consistency.

How to read the numbers. The capacity figures here are reference ranges taken from the product specification. Seamer stops, can-size changeover and downstream accumulation sit outside a rated CPH, so plan on 0.65-0.85.

Frequently asked questions

How many cans per minute is 18,000 CPH?

300 cans per minute. Divide CPH by 60. The seamer, the filler and the packer all have to carry that number, so the line rating is the lowest of the three.

Can a can line run both 330 ml and 500 ml?

Yes, with change parts for the filler, the seamer and the conveyor. Changeover time is the real cost. Two formats on one line normally means 40-90 minutes per switch and a lower production factor.

How often is a seam checked?

At a fixed interval during production, by tear-down and measurement, plus a check after every seamer adjustment. The interval is set by the plant quality plan; the point is that it is measured, not inspected by eye.

Why do cans dent on the conveyor?

Usually conveyor pressure or a jam at a transfer, not the can quality. Air conveyor pressure, guide rail gaps and accumulation length are the three settings to check first.

Key takeaways
  1. The seamer, not the filler, is where a can line loses its rating.
  2. Dissolved oxygen in the finished can is the number that decides shelf life.
  3. A failed seam is a roll and flange problem, found by measurement.
  4. Smaller cans raise the can rate without raising the litre rate.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.