How to Choose the Right Combibloc Filler for Juice

Views: 1558 Author: Howie SUN Publish Time: Update Time:
A juice line that runs at the right temperature holds shelf life; one that runs hot enough to deform the bottle trades shelf life for rejects.
Key facts at a glance
Filling principleHot-fill, up to 85 C
Rated output6,000-36,000 BPH at 0.2-2 L
PackageHeat-resistant PET geometry, or glass
LineHot-fill monobloc with tunnel pasteuriser
ProductsJuice, tea, nectar, functional drinks
Key controlFill temperature, hold time, cap seal

What actually decides the shortlist?

Four inputs fix the shortlist: the product, the package, the daily demand and the number of formats per week. Everything else, including the brand of the PLC, is a detail that can be settled after those four are written down.

What does the fill temperature actually control?

Fill temperature and hold time together set the pasteurisation result. Below the target, shelf life is at risk; above it, the product cooks and the bottle deforms. The number belongs to the product and the bottle, not to the machine, and it should be written into the acceptance protocol with a tolerance.

RouteTemperatureWhat it costs
Hot fillUp to 85 CHeat-resistant bottle and a cooling tunnel
Cold fill with preservativeAmbientFormulation constraint, not a machine constraint
Cold fill with in-line pasteuriserProduct-side onlySeparate pasteuriser and a closed filling zone
Hot fill in glassUp to 85 CGlass mass, slower line, higher transport cost

For the same duty in another bottle format, the Juice By Volumetric Filler is specified separately.

When is cold filling the better route?

Cold filling protects heat-sensitive flavour and colour and allows a lighter bottle. It needs either a preservative system or a validated cold chain, and it moves the microbial control to the product and the plant rather than to the filler. The decision is commercial before it is technical.

Site requirements, air and water consumption sit with the Hotfill Type Filling Machine for Juice.

What does a glass juice line change?

Glass brings mass, breakage and a slower line. It also brings a closure decision: crown, lug or screw. A glass hot-fill line usually runs at a lower rate than the same filler on PET, and the difference is handling and inspection, not the valve.

The same question is worked through from another angle in Juice Production in Vietnam, Thailand and Indonesia: Setup, Regulations.

How to read the numbers. The capacity figures here are reference ranges taken from the product specification. A rated BPH covers filling only. Pasteurisation, hold time and cooling sit outside it, so size on 0.65-0.85.

Frequently asked questions

What temperature is juice hot-filled at?

Up to 85 C, set per product and per bottle. The exact set point and tolerance belong in the product specification, because acidity, pulp content and bottle wall thickness all move it.

Does hot filling replace pasteurisation?

It replaces the bottle steriliser for acidic products, because the fill temperature and hold time do the microbial work. It does not replace correct product formulation or a validated hold tube.

Why does the bottle panel after filling?

Usually fill temperature above the bottle rating, or a vacuum that forms as the product cools. Check the fill temperature against the bottle specification and the cap seal before changing the cooling profile.

What cooling profile does a hot-fill bottle need?

A controlled ramp rather than a cold plunge, so the bottle does not deform under vacuum. The tunnel zones are set per bottle geometry and validated with a temperature probe in the product.

Key takeaways
  1. Hot fill does pasteurisation and bottle sanitising in one step, and charges for it in bottle cost.
  2. Pulp needs bore and agitation, not more pressure.
  3. Cap seals and valve O-rings are the first wear items on a hot line.
  4. Colour loss is a temperature and hold-time decision.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.