How Aluminum Can Filling Machines Handle Carbonated Soft Drinks

Views: 2122 Author: Howie SUN Publish Time: Update Time:
Aluminum cans fill faster than bottles and forgive less: dissolved oxygen and seam tightness decide shelf life, and neither is visible on the line. By focusing on pressure control, speed optimization, and maintaining carbonation during the filling process, manufacturers can enhance efficiency and product integrity.
Key facts at a glance
Valve typeIsobaric for beer and CSD, volumetric for juice and tea
Output rangeUp to 25,000 CPH
Can rangeStandard 250, 330 and 500 ml
SeamingRoller seamer integrated with the filler
OptionsHot fill for juice and tea, nitrogen dosing
Key controlFill level, seam tightness, dissolved oxygen

Why is can filling measured in CPH and not BPH?

A can line is counted in cans per hour because the container is the unit the seamer closes. CPH and BPH cannot be converted without the fill volume, and the downstream packer is sized in cases per hour. Comparing a 24,000 CPH can line with a 24,000 BPH bottle line compares two different plants.

By focusing on pressure control, speed optimization, and maintaining carbonation during the filling process, manufacturers can enhance efficiency and product integrity.

What does a can line cost to run that buyers forget?

Compressed air for the seamer and the air conveyor, CO2 for purging, and the tear-down cans used for seam checks every shift. None of these appear in the machine price. A line running 24,000 CPH can consume a measurable share of its operating cost in air alone.

ProductFilling principleCritical measurement
BeerIsobaric, coldDissolved oxygen and seam tightness
CSD and sodaIsobaric, coldCO2 retention and fill height
Juice and teaVolumetric or hot fillFill temperature and seam integrity
Energy drinksIsobaric or volumetricDissolved oxygen and closure

Throughput and change-part lists are on the Aluminum Can Filling Machine for Beer, Carbonated Soft Drink page rather than in this note.

What does a hot-fill can line need that a cold line does not?

A heated product path, a fill temperature control loop and a cooling tunnel after seaming. The can itself tolerates the heat; the lining and the product do not always. The temperature window belongs to the product specification.

The unit behind this configuration is the Aluminum Can Filling Machine for Hotfill Juice and Tea.

Why is can handling gentler than bottle handling?

Cans are light and rigid, so they move on air conveyors and mass conveyors with low back pressure. Dents come from jams and from accumulation pressure, not from the filler. A can line that dents is a conveyor setting problem before it is a machine problem.

The same question is worked through from another angle in Can Depalletizer Sizing: Speed, Layer Pattern and Buffer.

How to read the numbers. Every figure in this note is a reference range from the product specification, not a guaranteed output. A rated CPH is a steady-state figure at one can size; seamer adjustment and CIP sit outside it, so size on 0.65-0.85.

Frequently asked questions

Can a can line run both 330 ml and 500 ml?

Yes, with change parts for the filler, the seamer and the conveyor. Changeover time is the real cost. Two formats on one line normally means 40-90 minutes per switch and a lower production factor.

How often is a seam checked?

At a fixed interval during production, by tear-down and measurement, plus a check after every seamer adjustment. The interval is set by the plant quality plan; the point is that it is measured, not inspected by eye.

Does a can line need nitrogen dosing?

It is common for beer, juice and some CSD, where headspace oxygen has to be pushed down. It is an option with a consumable cost, so it belongs in the utility and consumable schedule, not in the base price.

Why does a seam fail the tear-down?

Usually seamer roll pressure, chuck wear or a can flange outside tolerance. The tear-down measures the result; the cause is found by checking the rolls and the can supplier specification together.

Key takeaways
  1. CPH and BPH are different units; never compare them directly.
  2. Beer and juice cans share a format, not a filling specification.
  3. A failed seam is a roll and flange problem, found by measurement.
  4. Smaller cans raise the can rate without raising the litre rate.
About the author
Written by the Sunswell engineering team - led by Howie SUN, Founder & CEO, with 14 years in filling and blow-moulding equipment R&D and turnkey project delivery across 71+ countries.
Last reviewed: 2026-08-28 . Reviewed by Sunswell engineering team
×

Contact Us

captcha

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.

×

Inquire

*Name
*Email
Company Name
Phone/Whatsap
*Message

*We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.